Found a John Deere 1010 Gas in decent shape for $1000. I think it is a row crop. Thoughts?

My 1010's tranny input shaft seal needs to be replaced. Question is, can I split it at the seam between the aft end of the bell housing and the front of the tranny, or do I need to split it at the...

I'm looking for ideas to mount a truck snowplow in the bucket of my loader :)

I'm restoring a john deere 1010 utility diesel I've rebuilt it from front to back but I can't seem to figure out where this line goes my book doesn't show it maybe a over flow ? any help would be...

Good evening all, I got the old 1010 from the old homestead, she is really in bad shape. I figure I would get tires back on her so I can move her around the shop. One tire is completely...

I have seen many posts with steering gear problems on this tractor model. Very poor design with 2 pins worked by a worm gear. Replacement parts are impossible to find so when mine wore out, I...

I am brand new to this site and I have a question regarding a JD 1010. I am wondering where is the best place to find the value for this vintage/antique tractor that is in running condition...

Need to remove radiator has power steering unit thru top of rad. Not sure about where to start with p/s unit removal help please thanks.

Hello, has anyone ever installed a rear main crankshaft seal in a 1010 gas engine crawler? The repair manual I have says to pull the oil seal plate off the block to install the new seal but I...

Hello, I have a John Deere 1010 Dozer(I think early 60"S). I bought it and got a great deal on it because the guy said the engine and trans were seized. Originally I was just going to use it for...

Looking to sell a tractor that has been in the family since 1962. My grandfather purchased this one new and my dad used it up until he passed away last year. My mom would like for it to be sold...

I have a 1962 John Deere 1010 that doesn't get used enough to keep it around the house. It's a gas burner and really nice mechanical shape. The seat is gone and the lights do not work. The paint...

I would like to replace the fan belt on my 1963 1010 and would like to know what has to be taken off to do so?

need to find a description on how to change the clutch on this tractor . I will have to split the tractor as well

Hi there, I`m new to this fourm and this is my first post. I recently bought a 1962 John Deere 1010 RU. Engine runs great, and the PTO is live. However, when I hook my bush hog (5 ft Bush hog...

Hello all thanks for reading my post. I will give you a brief history of the tractor i have. I bought it in november of last year, when i bought it i knew it needed a clutch and it would be a good...

I found this John Deere 1010 with a wide front end. I have not set my own two eyes on it yet, have only seen pictures of it. Man wants 1000 dollars for it as it sets. He says it was/is and will be...

Hello folks, My 1010 will start and run for about 5 minutes then it shuts off. Had the carb rebuilt, new plugs and wires and it still does the same thing. The sediment bowl is clean and I am...

Need help guys....had the carb rebuilt and put it all back together. Now, the tractor starts good and runs for a few minutes great then dies. New plugs and wires as of today....plenty of gas in...

Hi. Recently found a 1964 John Deere 1010 parked in a pasture. Said nothing was wrong...just quit using it and walked away. Considering purchase. Anyone have an opinion or experience?

needs point gape and spark plug gape for this tractor can somebody help. Had it running today then could not start again. I will have 2 fresh charged batteries. It needs a tune up. the carb has...

For those of you who have been helping me along the way this is the end result. Bought this about 15 days ago out of a brush thicket. Had been there for atleast the last 14 years, as I drove by...

looking for a 1965 john deere 1010 hydraulic pump. If you have one for sale please contact norm at norlor95@yahoo.ca

Hi, I am looking for a good used or new exhaust manifold for a John Deere 1010 gas tractor. Thank You, David

Hi, I am looking for a good used or new exhaust manifold for a John Deere 1010 gas tractor. Thank You, David

Hi Guys, An elderly neighbour has a JD 1010 4 cylinder tractor with a JD45 FEL on it. As far as I know it is in pretty good shape and until last year, was used to pull plough and discs...

I have a john deere 1010 .At the top of the radiator next to the main coolant tube .there is a device about the size of a can of baked beans .it attaches to the radiator and seems to attach to the...

I'm looking to maintain some logging roads and skid some firewood out of the woods, maybe even build up the low spots of the logging roads I have. Is a John Deere 1010 Dozer too small for anything...

Hello John Deere guys !! We are helping a friend try to get his 1010 running and we are stumped. Is there any quirk about these tractors that we might have missed? It is a gas tractor, 12 volt...

I have a 1964 JD 1010. It steers well travelling at lower speeds but at high speeds if I hit a big bump the wheel can jump sideways and make me turn without any control and while turning it will...