Bought a Massey Ferguson 1260 tractor a few months ago only to find out the head is cracked and unfixable. Having a hard time locating a new cylinder head. Any suggestions where to go?

I have a mf 1260 from auction . Was never used as a tractor. Nothing on the 3pt was ever hooked up or used. The lift arms are all the way up. Fo I need to put something on the 3pt to get them...

Where do you find the place to fill up the hydraulic fluid?

I have a 1260 up north. I need to build a boom pole for it. Anyone have one that could give me some dimensions for the rear mount so i can start building the boom pole. Was going to make it out...

Hello all, We have had a Massey Ferguson gear drive tractor in the family for years without issue. It has sat for a while until recently. It has a newer battery on it, and will start very well if...

Hey folks, Have a question about my Ferguson 1260. Past two winters we have a a low power/no power issue with the tractor in the colder weather. The tractor has a working block heater and starts...

Hey guys, I am going to be converting my 1993 Massey Ferguson 1260 from turf to R1 ag tires. The turfs are 212/80 d15 and 355/80 d20. I already sourced the 11x24 rear rims and centers. I spoke...

Hello, I need to repair a friend's Massey 1260. I think it is a copy of an Iseki compact tractor but don't know which model. I am tearing the engine open cause my friend bought it non working but...

Had a brush fire back in April. Burned up my 1260 and my old International that I think was approximately 400 years old. I've checked your typical classifieds/sales sites. Found plenty, but...

hi all, I was asked to look at a friends MF 1260 diesel. It's not starting when cold. I'm not very experienced with diesels. The engine has 3 glow plugs connected with a bar that runs across...

Need a complete front axle for a 1994 MF 1260. Pretty sure the 1240, 1250, and 1260 models used the same axles. Not sure of what years were the same. Bridgeport, West Virginia.

I am looking for a radiator for my 1986 Massey Ferguson tractor. I would prefer to find a used one in good condition.

Hi All, This morning the tractor would not start! Just some clicking sounds maybe from the fuel pump and some sound like a marble dropping but, nothing from the starter. There are 3 wires going...

I have a MF 1260 bought new in the 90's and recently bought a used woods 750 back hoe, that is mounted on a sub frame... the seller thought it was from a mihindra, but didn't know... I do know the...

The engine will not shut off after the key is switched off and key is removed. I have replaced the switch and still have the same thing. Have to stall the engine (pop the clutch in 4th gear) in...

I am looking for parts or a complete engine for a Massey Ferguson 1260 . The engine is a Iseki E3CD-T . Having trouble finding a Cylinder head for it. Any ideas of a good source for parts for this...

Hello! I am new to the forum... and to tractors. Just finished my first season as an organic farmer, and I am looking to buy my first tractor this winter. Budget is limited. Here is what I have...

I bought a used MF 1260 and the wiring is in bad shape. I know very little about wiring but how hard is it to use a wire harness and rewire? Don

Hello all. I am new to this site and am seeking advice on the best loader to try to find for our MF 1260. I would like to find a used one, but if I had to would consider new. I have been trying...

Does anyone have experience using a MF 1260 or AGCO ST40x (equivalent tractors) to move large (5x6 or 6x6) round bale hay? I know that bale weight varies depending on moisture, tightness, etc. so...

I have discovered that my FEL (1246) is connected incorrectly on my 1260. The previous owner mickey-moused the connection, teeing into the 3PH/draft control return. This is causing some dangerous...

I just bought a MF 1260/1246 FEL + 9 implements which is being delivered by truck sometime this week-end. I'm going to have to drive the tractor the last two miles since the semi can't get out my...

Hi from Canada, just joined the forum. Recently inherited 332 acre piece of land the hard way; father-in-law suddenly died, and took all his experience and know-how with him. Had to move from city...

I have a Massey Ferguson 1260 with a 3 cyl Iseki turbo deisel engine. The engine has a cracked block from a hard impact with the bucket. I guess these tractors weren't made for many years and I'm...

Looking to confirm year and HP of a MF 1260. The serial #is a H - H 1005. Also would anyone have a link or a copy of the owners manual? Thanks In advance.

I have a MF 1260 and I want to install a single spool remote to drive my new Markham grapple. Anyone have any ideas where to start looking for a compatable kit? WRLong doesn't have a kit for my...

Hi all, The 1260 now has 480 hrs. The other day I was driving and it seemed that the power assist was lost. I checked the fluid and it was good. You can see the fluid move in the reservoir tank...

I am planning on changing the transmission/hydraulic oil for my MF 1260 tractor. The owners manual recomends Permatran III, which is very expensive, or SAE 80 GL4. The local oil company does not...

Hello all. This is my first post. After months of looking and reading, I recently bought a nice used 1260 with fel and thus far am pleased that I think I bought the right tractor for my needs. I...

MF 1260 with loader My brother-in-law found a 300 hour old 1260 with FEL. also comes with a brush hog and rear blade. What is it worth? Stated price on it is $14,900. Is that good?? Any...

I'm looking at a used mf 1260 with about 150 hours. The price seems good at $10k, but I'm wondering about the capabilities of this little machine. The specs say that it has 31 h.p. at the PTO...