Making hard line - fittings needed
- Thread starter john_bud
- Start date
- Views: 2801
Egon
Epic Contributor
Swagelok fittings??
No welding or brazing required. Lots of hits on google.
Tube Fittings for Leak-tight Connections - two-ferrule tube fitting by Swagelok
No welding or brazing required. Lots of hits on google.
Tube Fittings for Leak-tight Connections - two-ferrule tube fitting by Swagelok
joes_427_vette
Veteran Member
- Joined
- Aug 10, 2004
- Messages
- 1,273
- Location
- Midwest
- Tractor
- IH Cub Lo Boy, 955 John Deere , TC 55 DA New Holland, Bolens HT 20 and 1456
Did you try J & D Tube bending out of Schofield ? I have seen some of their work and their bending forms are very pleasing to the eye.
Joes...
I have all the skills in the world for bending these tubes (they are straight!!). What I need are fittings that make a 90 degree turn and go thru a bulkhead. It really shouldn't be that tough, I'm just looking in the wrong places or using the wrong google words. I can get billions of hits that I don't want! Pounding head on desk....
And, no I didn't try J&D, but I will look....
Thanks,
jb
I have all the skills in the world for bending these tubes (they are straight!!). What I need are fittings that make a 90 degree turn and go thru a bulkhead. It really shouldn't be that tough, I'm just looking in the wrong places or using the wrong google words. I can get billions of hits that I don't want! Pounding head on desk....
And, no I didn't try J&D, but I will look....
Thanks,
jb
Egon
Epic Contributor
John, I just tried to locate some. Now there is two sore heads.
Can your local tubing supplier be of help or say a local backhoe dealers service shop?
Can your local tubing supplier be of help or say a local backhoe dealers service shop?
tommu56
Elite Member
john_bud
I for one of those sunday repairs I have drilled out a female pipe to jic or found male fiting with the same bore as tubing size and brazed them on.
something like this SAE 37° Flare (JIC) Bulkhead Tube Union 90° Elbow
tommu56
I for one of those sunday repairs I have drilled out a female pipe to jic or found male fiting with the same bore as tubing size and brazed them on.
something like this SAE 37° Flare (JIC) Bulkhead Tube Union 90° Elbow
tommu56
3RRL
Super Member
- Joined
- Oct 20, 2005
- Messages
- 6,931
- Tractor
- 55HP 4WD KAMA 554 and 4 x 4 Jinma 284
John,
Did you try here?
Discount Hydraulic Hose.com
Or here under fittings?
Surplus Center - Hydraulic Cylinders Pumps Motors
Did you try here?
Discount Hydraulic Hose.com
Or here under fittings?
Surplus Center - Hydraulic Cylinders Pumps Motors
YEah, tired those. May have to go to a ferrel type solution, but I REALLY REALLY want a silver solder, braze or weld on 90 degree bulkhead for 3/4 steel pipe.
The stinking backhoe is full of them! They can't be that impossible to find ... banging head on table ... they just can't be...
can they?
j
The stinking backhoe is full of them! They can't be that impossible to find ... banging head on table ... they just can't be...
can they?
j
tommu56
Elite Member
john_bud
why not use the furrel fitting and throe out the nut and furrel and braze them to gether
from discount hydraulics
or use 27208-12-12 compression adaptor and 6500bt-1212
or give them a call mabe they have what you want but not on internet?
tommu56
why not use the furrel fitting and throe out the nut and furrel and braze them to gether
from discount hydraulics
or use 27208-12-12 compression adaptor and 6500bt-1212
or give them a call mabe they have what you want but not on internet?
tommu56