Hydraulics hook up on YM1700

   / Hydraulics hook up on YM1700 #1  

Eddie

Platinum Member
Joined
Jul 8, 2003
Messages
548
Location
North Alabama
Tractor
YM2020 & Allis Chalmers 6060
Anyone have a FEL on a YM1700 that could post a picture of how the hydraulics hook up. Like where they hook up, under the seat or down on the frame? I was thinking I would like to do the quick disconnects so it would be easy on and off.

thanks
Eddie
 
   / Hydraulics hook up on YM1700
  • Thread Starter
#2  
Surely SOMEBODY does!!!!!!
 
   / Hydraulics hook up on YM1700
  • Thread Starter
#4  
It really doesn't. I would like to see what others use for fittings, lines and exactly where they cut in the line that is the most likely not to have problems later. I started the other thread so I had already read that, thanks.
 
   / Hydraulics hook up on YM1700 #5  
OK, here's what is needed: 2 compression fittings for the high pressure line. 2 fittings that match the valve inputs/outputs. U might need: 2 right angles for the compression fitting. 2 adapters to adapt the compression fitting outputs to the size of your valve I/O lines. Cut the highpressure line and use that to size the comprssion fittings. If you have a hydraulic shop near by take the valve & cut out piece of high pressure line to get the correct fittings. Don't forget the measurements so they can build the lines. If you are ordering the parts and fon't want to cut the line til the last minute use a micrometer to get the OD measurement of the high pressure line. It's relatively easy after you do it once, and I've found that it's not too hard to make mods or add more hydraulics.
 
   / Hydraulics hook up on YM1700 #6  
Here is a photo of my 1810 where the hydrauics were tapped for the loader.
 

Attachments

  • 718270-hydraulic_connection.jpg
    718270-hydraulic_connection.jpg
    59.4 KB · Views: 305
   / Hydraulics hook up on YM1700
  • Thread Starter
#7  
Thanks Gary, That's what I'm looking for.
 
   / Hydraulics hook up on YM1700 #8  
Here is the hook up on a YM1500D. Not a very good pic, but you may get the idea. It was set up so that you could take the loader off and then reconnect the lines.
 

Attachments

  • 718291-YM1500D loader mount.jpg
    718291-YM1500D loader mount.jpg
    51.3 KB · Views: 367
   / Hydraulics hook up on YM1700
  • Thread Starter
#9  
Brent, do I see 3 lines connected on your 1500?
 
   / Hydraulics hook up on YM1700 #10  
No, they are just looped around and it gives the appearance of 3. The two quick disconnects you see are the spliced in lines of the supply line. The small connection you see to the left the return line from the FEL with a compression fitting on connecting it back in series.
 

Tractor & Equipment Auctions

2014 FREIGHTLINER CASCADIA (A50854)
2014 FREIGHTLINER...
2019 VOLVO VNL HIGH ROOF SLEEPER (A50046)
2019 VOLVO VNL...
2013 Ford Escape SE SUV (A50860)
2013 Ford Escape...
2018 International WorkStar 7400 T/A Dump Truck (A50323)
2018 International...
American Sanders EZ-8 Electric Floor Sander (A49461)
American Sanders...
2013 Ford F-150 XLT - EcoBoost, Blown Engine, Good Parts Truck (A51039)
2013 Ford F-150...
 
Top