Search results

Sorry I haven’t updated so here goes. Shortly after my last post I purchased a Kubota Mx 5200 gear drive with shuttle,250hrs. It has rear weights, one remote, heavy duty bucket, arm rests and bucket level indicator all of which are optional. Long story short, today I ordered a LS mt357 pctc cab...

I’m looking to buy a Rototiller to run behind a Kubota MX 5200. Any suggestions regarding width and forward or reverse rotation?

Thanks for the heads up. Maybe I can get a senior discount also as I just turned 70 two days ago, time flies when you’re having fun. Yes the loader is included. I am going to look at the Branson 5835r at the end of the week. I’m a little concerned about the power clutch on the LS, it just seems...

Minor up date, going to look at a 2013 Branson 5220C tomorrow. Add states it has 35 hrs. and lived indoors its entire life. Either a barn find or bs,it remains to be seen. I assume there would be no dpf on this tractor., if someone could confirm that it would be appreciated.

Does anyone have any experience dealing with J and K auction and sales in Flint Texas? They seem to have a lot of low hour tractors at reasonable prices. Thanks in advance.

The pricing is within a few hundred dollars. The Branson dealer is tractor and implement dealer first, the LS dealer is a forklift first dealer with 5 or 6 locations, each of which sell LS tractors. The dealer closest to me has 12 to 15 new units and around 60 out on rental, they have been...

Does anyone have any experience with a mt357? I drove one the other day and it seemed pretty comfortable and well laid out. I have a quote of 34,xxx otd delivered, it seems like a fair price. I am also looking at a Branson 5835r which seems pretty much like apples to apples. Ls dealer is 25...

Anyone own or have any experience with a Branson 5835r? Good or bad?

Anyone have any experience with a Branson 5835r? Good or bad?

How do you like your 2760e? Any dislikes or problems?

Does anyone own or have any information on the 2750e? I know it has a Shibaura engine but where is the tractor manufactured?

I don’t know where you get the 15 hours. It is an open station tractor. I know it not a simple task but that seems excessive. My concern would also be the clutch.

That comparison was actually for a DK5010. I would expect a similar 5510 would be 1500 to 2000 more based on the difference between a 4510 and a 5010.

It would be approximately $6000.00 more.

In service date was 3/20/20.

The remaining full warranty expires 3/20/22, the emissions warranty expires 3/20/25 and the power train expires 3/20/26. The tractor was a rental that was used in the vineyards, the loader is being added now along with top and tilt. There have been two warranty claims one for a hydraulic seal...

I 'm looking for opinions on a 2019 DK5510. It has 1100 hrs. on the clock, new fel, telescoping lower links and stabilizers and is gear drive with a mechanical shuttle. It has the remain factory warranty and appears to bear in good shape. Can get for $25,500, otd. What do you think.

Before going to look at a Ford 10' offset disk I would like an opinion if my 83 hp 4wd tractor is enough?

Thanks for the pat on the back.

I just bought the tractor for $19,000. I have my fingers crossed.

I just recently went to see the tractor and yes it has been unused for quite some time. I was wondering if the clutch could be an issue, even with the low hours a clutch on the wrong foot can be a disaster.

I have already been there. I am sure somebody out there has had some hands on experience with this tractor. There is one for sale in my area; 2007, cab,700hrs,and very clean, $20,000, however it seems to shift kind of hard, kind of like you are searching for the slot. Anybody?

Does anyone have any information about this tractor?