Search results

Results 1 to 41 of 41
  1. T

    Fuel injector “0” ring question

    Is there anything special about diesel fuel injector “0” rings?. Can’t seem to locate replacements for Bosch injectors but I’ve got a large assortment of Viton “0” rings and I’m sure I can find one that’s very close. I assume the Viton rings should work if I can find a close enough replacement?????
  2. T

    Is there a fuse for temp gauge Kubota M6800 cab tractor

    Temp gauge died in M6800 cab tractor. Replaced the sending unit but still inoperable. Grounded wire to block and gauge doesn’t react. Possibly a brake between sending unit and gauge but I don’t care to chase it down if that’s the case. I’ve seen conflicting information regarding a fuse but I...
  3. T

    YM2000D Motor oil Capacity

    YM2000D Motor oil Capacity This is a 4wd YM2000D not to be confused with the YM2000 2 cylinder. This is a 3 cylider engine and I'm trying to help an elderly friend do an oil change and can't find anything on the net.
  4. T

    How to wake up diesel engine that’s been sitting about 3 yrs

    My dad passed away a couple of years ago. He owned a stump grinder at the time. It’s been sitting in the barn since he passed and I haven’t had the will to touch it. I finally decided it was time to get it fired up again. It’s a Rayco 1642 with a 42 hp, air cooled 3 cylinder duetz diesel engine...
  5. T

    Kubota M6800 Cab Tractor Temp Sending Unit

    Was mowing with my M6800 yesterday and the temp gauge died a few hours in. My Kubota has a bucket and that limits access under the hood. I removed the hood then the air intake but I still can’t find the sending unit. The next thing to remove is the exhaust system which I hope to avoid...
  6. T

    WTK: Difficulty To Do Inframe rebuild on YM2000???

    How difficult is an inframe rebuild for someone with average to above average mechanical skills?? It’s come to the point where I’m going to rebuild or have someone rebuild the engine in my trusty 2 cylinder YM2000. It still runs but it’s burning oil, had limited power and excessive crankcase...
  7. T

    WTB: Compatable Front Wheel Yanmar YM2000

    Please let me know if you have one for sale.
  8. T

    Used Front Wheels YM2000..???

    I see several vendors selling new front wheels but I would prefer a good used one if possible. Ive seen several on eBay but none are currently listed. The old one has been cracked for years and it recently started wobbling. I think it’s time for a replacement before it fails.
  9. T

    DIY Chain Drag Repair..????

    I知 missing a couple of sections on my well used chain drag. Is there a way to to make repairs.? I could probably find a shop to make the repairs but that would likely cost more than it逞エ worth.
  10. T

    What's it worth,,??? See Pix

    This Montana belongs to a neighbor and he's thinking about selling it. He purchased it new. The hour meter is showing about 500 hours and it has been sitting in the elements for a several years. He said something was wrong with with the HST and a mobile mechanic bypassed the glow plugs. I know...
  11. T

    Source for aftermarket John Deere 503 Rotary Cutter Blades..???

    I have an old Deere 503 rotary cutter that could use a set of new blades but I want to save $$$ if possible and buy aftermarket. Can anyone point me in the right direction? I don't see why these wouldn't work?? CountyLine 5 ft. Rotary Cutter Blades, Pack of 2 at Tractor Supply Co.
  12. T

    Difficulty to replace rings Yanamr YM2000..?? Is it a DIY job..??

    The crankcase blow by on my trusty YM2000 has become quite excessive and it's not going to improve on it's on. I have never replaced rings on anything but I'm a fairly decent shade tree mechanic. I split the YM2000 last year and replaced the clutch with relative ease. I know the block is...
  13. T

    Stupid question but...How often do you replace blade bolts on rotary cutter..??

    Tomorrow I'm pulling and sharpening the blades on my old Deere 503 rotary mower. Not sure how old it is since I purchased it used years ago but I'd say it 30ish years old and I'm going to assume the blade bolts are original. I searched the net and couldn't find any recommendations on how often...
  14. T

    Can Someone ID my Disc Harrow C-Pix

    Purchased this old disc several years ago along with a Yanmar YM2000. It's served me well working on small food plots but it's starting to have issues. I doubt parts are available but at least I could look around if I knew who made it. Unfortunately the neighbor I purchased it from passed a...
  15. T

    Local Tractor Dealer Recently Dropped Yanmar..

    Local Tractor Dealer Recently Dropped Yanmar. Is anyone else seeing this where they live? I own an old Yanmar which I love but always thought the brand to be a rather small niche market. I had a feeling this was going to happen after I stopped by my local dealer and looked at new Yanmar...
  16. T

    Rotary mower v Finish Mower pulling down Yanmar tractor. HP Requirements..??

    I have a YM2000 that will pull my old 5' Deere rotary mower all day w/o any problems. I recently purchased a used Deere 261 finish mower that appeared to be in very good shape. I removed the drive belt and hand spun every blade to check the spindles and replaced all the blades at the same time...
  17. T

    Mahindra 3616 4WD Cab Tractor info please...

    I've owned Deere, Kubota and Yanamr over the years but I'm clueless regarding Mahindra. I located a great looking 2012 Mahindra 3616 4WD Cab Tractor with cold AC and FEL for sale locally with 450 hours. Does not have hydrostat transmission and the AM/FM radio does not work. ] I know Mahindra...
  18. T

    Tell me about TYM tractors...Looking at tractor in link.

    I know nothing about TYM but the prices almost seem too good to be true. td New 39 HP 4x4 Cabin Tractor & Loader - farm & garden - by dealer - sale
  19. T

    3 Point lift Bogging Engine YM2000

    I know y'all must be getting tired of my questions. I swear I'm getting close to debugging this tractor so please bear with me... When I lift the 3 pt hitch to maximum height it drags down the engine. It does just fine as long as I stop the lift an inch before it reaches maximum height. Am...
  20. T

    YM2000 will not pull JD 261 5' finishing mower

    My YM2000 does a decent job pulling a JD 503 5' rotary mower. Today I hooked up a JD 261 5' finishing mower I recently purchased. I greased it, replaced the blades ETC and the cut was amazing but it seemed to be putting a heck of a strain on my tractor although my grass is pretty splotchy and...
  21. T

    Looked at a new Yanmar YT235 this afternoon.....

    I have an old Yanmar YM2000 that I dearly love so I was happy when a local dealer recently started carrying the new models. This afternoon I checked out a YT235. I found the looks quite odd especially the headlights. The controls seemed awkward. I was also surprised to learn it was priced...
  22. T

    HELP: Oil Dummy Light Staying On Yanmar YM2000

    I recently replaced the damaged/missing dummy lights on my YM2000. I also replaced all of the sending units at the same time. Everything has been going OAK for the last 4 weeks while planting a garden. This evening I started it up and the oil light stayed on. I checked the oil level and it was...
  23. T

    WTK:Best/Cheapest place to buy replacement discs

    I need 14 24" x 1 1/8" square hole discs. Any good online sources that won't kill me on shipping..?? td
  24. T

    Tried to configure a new SA series on Yanmar's website

    The website is mostly useless and it won't allow you to configure a tractor. How in the **** does Yanmar hope to make inroads in the US market if their website doesn't even work..?? td
  25. T

    Charge Light Staying on YM2000...??????

    Just finished replacing dummy lights, old style fuse block, ignition switch and some jacked up wiring on my YM2000. Had the alternator tested several months ago and it was OK but that doesn't mean something hasn't changed since then?? Everything seems to be working surprisingly well but the...
  26. T

    Replaced the outdated fuse panel in my YM2000 tonight

    Purchased the fuse box conversion kit from Hoye. FUSE BOX CONVERSION - CONVERT TO NORMAL BLADE FUSES!: Yanmar Tractor Parts I was torn between it and the generic replacement for about 1/4 the cost from Amazon or Ebay. I'm glad I purchased the kit from Hoye. It was direct fit and was shipped...
  27. T

    Is there a trick to remove headlight switch YM2000..???

    I'm having a hard time removing the headlight swith. I know there must be a trick but I can't seem to figure it out. td
  28. T

    What gauge wire should I use to rewire my YM2000..??

    I'm taking about the accessories like headlights, sending units ETC not the starter.... td
  29. T

    WTK:I need the torque specs for clutch/pressure plate YM2000

    Google let me down this time. td
  30. T

    Split my YM2000 this afternoon...C-Pix..Have a few questions.

    Pretty simple to split... Had her apart in about an hour. I have a few questions for those who have been there...done that.. I assume I need to remove the large nut in order to remove the flywheel so it can be turned. Is there a torque spec I need to be aware of when I replace the flywheel...
  31. T

    Comparison  Difference in quality on Yanmar YM 2000 clutch from Hoye or Ebay

    I'm getting ready to split my tractor in half and replace the clutch. I can save a few dollars buying a clutch off Ebay. Is there are difference in quality compared to Ebay or Hoye..?? I am a big believer that you get what you pay for but I suspect there's only one company manufacturing most of...
  32. T

    How difficult to replace crank bearing...???

    I've located a nice looking Yanmar 2500 for sale for $800.00. I haven't spoke with the seller but he says the crank bearing needs replacing. Is this a DIY type job for someone with basic mechanical skills..?? This would be a great parts tractor for some one with a 2500 but I'm not sure if...
  33. T

    Dummy lights not working on Yanmar YM 2000

    My Yanmar has three dummy lights on the dash that have never worked. I found the bulbs and harness flopping around under the hood when I purchased the tractor and now I'm ready to repair them but I'm not sure where to start. Whats the best way to tackle this project?? td
  34. T

    PLEASE HELP: Can't Start Yanmar YM2000 after Fuel Filter Replacement

    Changed out the fuel filter on my Yanmar YM2000 and I can't get it to start. I refilled the plastic fuel bowl after I replaced the filter. When I fired it up it ran for several seconds died and would not restart. Per info I located online I then opened the pair of bleeder screws located above...
  35. T

    Eicher Tractor Replacement Parts Source????

    I found a seemingly good deal on a Eicher 364NC 35hp diesel tractor. Good looking tractor mfg'd in India sometime in the 2004. Try as I might I can't find a source for replacement parts. I even located a post where someone was searching for an oil filter. Is anybody familiar with this...
  36. T

    Can someone please tell me which Allis-Chalmers bottom plow I have

    I'm trying to locate replacement wear parts for a 4 point AC bottom plow but I'm not sure which model I have. I know parts are difficult to find for AC implements but they are darn near impossible to find if w/o know the model number. Thx td
  37. T

    Traction  Kubota M6800 With Cab...Front Differential Hard to Lock In

    Been really difficult to operate the lever to lock in the front differential on my M6800 with cab. I briefly got under the tractor tonight and couldn't see anything bent or broken. I sprayed everything with a light lubricating spray while I was under there but didn't notice any improvement...
  38. T

    Look what followed me home today

    I'm the proud new owner of a 12 foot pull behind Poplarville harrow with 24" discs. I towed it almost 40 miles home on ancient dry rotted retreads and I was relieved when I made it. This thing is heavy duty but it needs a little attention after sitting up for many years. It needs new...
  39. T

    I need info on Popularville Mfg Co Disc Harrow See-Pix

    Are there any parts available for this harrow..?? Any opinions on average value in this condition..?? What's the consensus on this mfg's overall quality..?? It's been stored in a covered pole barn for at least 10 years. Thanks in advance...!!!!! td
  40. T

    Who Makes a "PM Company" Disc Harrow..??

    This afternoon I looked at a 12' pull behind disc harrow. According to the seller it had been sitting under the shelter for 10-12 years. Other than that she couldn't tell me much. It was well used but it appeared to be a quality implement. I have searched the net but so far I have failed to...
Top