Search results

I was hoping to put a cessna valve from a John Deere loader onto a ford 3000 tractor. the john deer valve is alot smaller than the one off the Ford. Smaller inlet and outlet and spools. im guessing that wouldnt work ? what I want to do is put on a valve that would have down pressure on the lift...

I have a old 1250 grasshopper mower 44 inch deck. the deck pulleys are shot also the deck belt. probably could use new spindles or bearings. Where can I find the best deal on these parts. I have a 185 JD that needs the same parts and a 140 that needs an engine. The grass is growing.

My dad has an erskine pull type snow blower. It has a flipper spout that will blow the snow to the left or right. the spout is on the rear of the blower, a rod goes from the chute to a position on the front is bent to a lever to grab and flip the spout. Im hoping someone has made a better setup...

the electric clutch on my cub cadet 14 hp kholer 1 inch shaft recently dissassembled its self. The bearing was kinda dry and rough and ate the collar that the bearing turns on. the three metal tabs that connect the bearing to the clutch plate broke. It looks to me that if I heated the clutch...

my dad has a ford 3000 with a lucas generator which is not charging. The plate on the back end of the gen is broken. This is the back cover and the rear mounting bracket. Where can I get a replacement bracket? I would like to replace with a alternator but the tack drives from the generator. Is...

I want to build a two seat buggy for around the yard, 4 wheel drive would be best. any suggestions?

I bought a columbia vice for 5 bucks. Its missing one jaw. any body know where I can buy a replacement jaw? It fits into a slot and is held in place with three pins. model # 604 - 4inch jaw

we have a loader that origionally had only lift rams [one hose on bottom.] replaced rams hooked hoses on both ends for power down. plumed to valve, it doesent seem to be sending oil to return stroke. what changes need to be made to the valve to operate correctly? bucket comes down slow and stops...

My dad just bought a ford 3000 tractor. it has an 8 speed trans, when you engage the pto it grinds and does not want to engage. seems to work fine when it is engaged. the lift hyd. cylenders need to be replaced, where can i find them? there is a small lever on the rh side of the trans what does...

I need a electric or mechanical clutch to fit on a inch and 1/8 shaft. im replacing a 14 hp kholer with a 16 hp kholer on my 140 JD. the 14 hp had a inch shaft the 16 has 1 and 1/8. a new clutch is about 250 bucks. what are the alternatives?

I would like to buy a small mig welder. are the 110 volt ones worth buying? im sure 220 is better, I have to run a 220 extension cord to my garage which is a pain. Which brand is best?

i recenty aquired a cub cadet im using to blow snow. lifting the snowblower with the deck lever is a pain. is there a lift assist spring or another type of lift? also need a muffler for the kholer eng and ect.

my dad has a 6000 uses it for blowing snow and mowing grass. it has a bad leaking front trans seal it still works ok would it be worthwile to replace the seal? im sure some damage has been done to the selct o speed. the brakes and 3 point arent working, the power steering is. I think they all...

I switched bearing plate and flywheel on my 16 hp kohler now have electric start an runs good. I was going to put the electric clutch from the 14 hp on the 16 hp but the shaft on the 16 hp is 1 1/8 and has no threaded hole ( 14 hp has inch shaft and threaded centerhole. Any sugestions Is there a...

my 14 hp blew the rod I bought a used 16 hp k341 I want to switch parts and put the electric start and batt ignition on the k341. I believe the bearing plate and flywheel will interchange. How do I bench test the stator b4 assembly? any advise on this will be appreciated. the throttle...