Search results

I've been all over the web looking for #1- a parts manual, and #2- the correct part. At one point I found a new-old stock complete pump but my web service went down before I could order it. Any help would be greatly appreciated.

I just bought a new but preowned quick hitch for my 1986 38hp Ford tractor. Turns out Cat 1 is 29" wide, and while it will go on the lift bars, none of my attachments are wider than 22". Is there a company that makes a Cat 0 quick hitch? (google failure)

I've had this screen kicking around for several years. I picked it up as 'scrap' with a bunch of scrap during a clean up job. And I had a few red oak logs laying in the yard from this spring. (browntail killed the oak) So while milling lumber, and the last logs in the yard were the oaks, I cut...

So on and off though out the summer I've been cleaning up and pushing stumps that was dumped here 6 years ago. Yesterday I decided to dig in my pit and build up a small camper pad at one edge of the pit. This evening after dinner I was shaving a bank, and opened up (found) a nice vein of pin...

I'm looking for a direct fit VR for my 1986 Ford (Shibaura) 2110 4x4 Diesel. Search engines have been usless, trying to sell me everything that DOES NOT FIT! Ebaymotors and Amazon show nothing that will fit. (already returned one) Any help would be greatly appreciated!

[this subject is on a 1986 Ford 2110 fwd/diesel] So I am changing lout the old and tired 2-spool valve, to a new 3-spool. Of course, I didn't have all the parts on hand mostly because my working on tractors knowledge is limited to the past few years. Anyway, I checked the fitting and...

I'm looking to replace 1 (for now) 3 1/2" x 3/4" cast iron wheel on my old Northlander mill. The center hole in the wheel is 3/4" (19mm) and a rod bearing gets pressed in. The U-Groove rides on the edge of a 1/4" angle iron, unlike the v-groove which rides along the back of angle iron. In...

Since I can't find all the old(er) threads on this topic, and I may be buying a new valve body any way... would this work? [adding a grapple] Buy a 3-spool valve with float (on the left lever), then plumb the center lever for the bucket tilt (as usual), then plumb the third lever/spool...

The glow plug heater helps a little but it still only starts on 2 cylinders, and only when it feels like it. (black smoke when it tries to start) I was told today it may be a couple dead glow plugs. It started pretty well August/September, and always runs well and smooth once started. So...

So last January my hydraulics completely quit working. I don't have a shop so I left it 'til Spring' but I got T-boned in the car late February. Traumatic Brain Injuries (TBI) suck, and kept me sidelined until July/August when I could finally get back to the tractor issue. I found a young (22)...

Looking for pictures of the STANDS for when I take the loader off the tractor. I would buy a pair if 1) available, and 2) if affordable, but I am hoping to fabricate my own if I can get some photos. Thanks in advance.

I'm looking for one, but I'll buy two if I can find them... Any help appreciated. 1986 Ford 2110 radiator mount ( New Holland #SBA398115230 ) There are TWO Bolts in this photo, as they do not connect! It is not a solid bolt...

1986 Ford 2110, 38 hp, 4x4. I plowed the first winter storm back in January, parked the tractor. Out the next day and cleaned up the left overs, parked the tractor. 10 later we got snow so I warmed up the tractor to plow and had zero response on all hydraulics! Rather than fight the cold I...

I ordered a skidsteer plate from Titan 5 days ago, with a 4 day delivery schedule. Fives days later they haven't even shipped it. Apparently this is a huge problem for a while now from reading the hundreds of complaints on their fb page.

My FEL is most times slow to respond, comes up about a foot, stalls, then goes up smooth at 1500+ rpms. Letting the FEL down it responds well with initial stop but then creeps down 3 to 4 inches fairly quickly. I'm suspecting air in the system is causing this. Can anyone explain where/what line...

What have you guys built to skid logs out? I have heard of more problems with Farmi-style rigs, and I'm looking for simple rigs that just plain work for a part time logger. Bonus for photos...

1986 Ford 2110, specs online say 134a for this tractors hydraulic system. Of course when I look for "134a Hydraulic Fluid" I get all the sales pitches but find nothing pertaining to my search. Does this particular fluid have a generic name/brand/number? Or, what would be the replacement fluid...

On a DUAL loader, Ford 2110 tractor. Similar to skid steer mount, but uses a round tube top bar. Bottom clicks in like skid steer mount. Any ideas what it's called?

Been a while since I've owned a tractor. And it's been a while since I've been on this forum. I recently purchased a 1986 Ford 2110 4x4 with a Dual (brand) Loader. Large frame for a 38 hp, but it's old school and I can work on it without a Tech and fancy computer hook ups. Just wanted to say...

Can anyone here point me to the filler for hydraulics on this tractor please? The pump sends fluid to the loader, but also to the lift arm 3-pt hitch. New filter at the pump but I can't seem to find where to add fluid. I'm waiting for the service manual to get here. Just thought someone here...

With search engines the way they are, I can't find a real source for Montana tractor parts. Wondering if any of you know of a place that sells OEM and/or aftermarket parts like radiator hoses, brake and clutch pedals, cooling fan, complete air breather, etc. As close as I can figure, I have a...

Been a long time since I've been on here, hope to visit & read more... I just picked up a 2006 Montana 3240, but the frame tag says TOPA32. I'm having a tough time locating parts for it, and an actual paper manual for parts & repair. ( This poor tractor has been rolled off a trailer, and...

Last year [or 2010 maybe] I read a "how to" article on constructing wooden trusses for a greenhouse. 16' wide by 10' high I believe the measurements were. I looked through about 30 or more M.E.N mags today and can't find the one with the article. Can anyone help me out with the month/year those...

This is the new house I started building in May 2008. It is 28 x 36 one and two-thirds floors. It was designed and revised over the last ten years, still isn't perfect but it was all "out-of-pocket" and sweat! No power lines, only a phone wire until a new [more] local cell tower goes up. Sat TV...

I have a 1969 Case 430 (with the big loader on it) That keeps popping out of reverse. Never a problem with forward, just reverse. It is the shuttle shift [long stick on left side] giving me trouble... the 4-speed on the floor has no issues at this time. Actually, the tractor has no other issues...

I just bought a Case 430 with a backhoe on it. Problem is (or was) it was put on by a real genius using 3/4" threaded rod, then had plates welded (if I dare call them welds) to the frame. Threaded rods snapped in the middle and the >welds< came apart so the only thing holding the how on was the...

I have a chance to buy an I/H 330 (1958) for under two K, it needs a steering box. Is this part still available and how tough is it to change out? Is there anything else I should look for? (trouble???) Thanks, Jack

Goofing around on ebay and found this; NEW CABLE PLOW BLADE CHAIN ATTACHMENT - eBay (item 380002659589 end time Mar-10-08 13:49:07 PDT) Anyone know what it is?