Search results

I have burned down a patch of lawn with roundup and am getting read to put in some fescue at the end of September. There are several Gill pulverizers for sale in the $400.00 range nearby. I was thinking I could use it to prepare the seed bed. Will this be a worthwhile purchase? Will I be...

The blue one is the Mitsubishi FD1450D. Its older brother is the Satoh S-470 Buck.

Charlotte NC Craigslist has sheet metal, tires, 2wd front axle and other stuff for sale.

Here is mine on the S-470 Buck

A friend's tractor ran out of fuel. Pretty sure he's bled it right but still won't fire up. Any hints?

I just saw Jay Leno's TC34D sell on Barrett-Jackson sell for $535,000!!!!!!! Proceeds were for Fisher House, a charity that helps veterans.

My welder is just inside an open barn. Welded fine yesterday but today after a good rain I was getting set up to weld outside again. Started getting a tingle from the ground clamp after I turned on the welder. It is an old AC welder. How can I check my receptacle to see if it is wired...

The mighty Buck has been on loan to my brother pulling mostly cedar logs out of the woods for a new equipment shed. Thery were sawed into poles. Also, pine and poplar sawed up too by a Yanmar powered Wodd mizer.

Every now and then somebody asks about a screen for the radiator. I just had mine rebuilt on the 1450 FD. It was stopped up inside and out and the two side frames where it mounts to the tractor were loose at the bottom. Glad I did this when I didn't have to. This is my dedicated mowing...

My brother just bought a lightly used JX85 with 384 hours. It sat in a building without being started for a year or so. It has a new battery and spins the motor over seemingly fast enough but it takes 45 seconds or so to start it. Even when the engine is warm it is slow to catch. I'm going...

Hinges are short angle iron bolted to a creosote post with a short pipe welded on. The bottom one failed when the short pipe broke off after probably 30 years. Welded new short piece on today. Will put the hay forks on the Satoh Buck tomorrow to lift the gate into place so I can put it on the...

I'm in the process of fabbing a hitch for a friend. Brand is not important because the answer should be the same regardless. Doesn't the center of the hole for the hitch pin need to be in the center of the PTO U-joint?

I got one of these for Christmas to mount on my club car carryall. I will make mounting brackets and need a measurement please. What size outside diameter is the tubing for the front and rear racks on most four wheelers?

I need wheel bearings for a small trailer. Can buy a bearing kit for $12.99 at Northern Tool or a hub with pregreased bearings installed for $30. Are these bearings OK? The kit at NAPA is $32, just the bearing kit. What do yaw think?

I helped my brother make hay last Friday. It was some pretty good fescue and I was raking with a Kuhn speed rake and a Case-IH 485. This tractor is a diesel but has the exhaust and muffler under the tractor. I was making a turn in a tight corner and crossed a windrow. A big wad of hay...

1. A friend has one and I think his glow plug indicator is toast but the plugs are still working. Is that possible? I thought the power went through the indicator. 2. Is there a non grey mits or satoh that uses the same starter switch as this tractor?

Looking for a 25mm 18 spline yoke that slips on the tractor stub. Preferably off a small Woods mower. Most likely counter clockwise rotation. Used is fine.

I can see thumbnail attachments but not other pictures in a post. What's wrong?

Tried to poke it out with a tape and water hose but ran into a blockage right where there is a willow oak. Most likely I have a root problem. Can this be fixed by some type of drain cleaning machine or will it have to be dug up?

Do the 2350's ever have drawbars that are mounted on the bottom of the rear end housing?

A friend has a 2050 with a 5' bush hog. I ran it yesterday for him as he is not able right now. What is the correct engine rpm and what pto gear is correct. I used pto 2nd and ran about 2200.

This is one of about 2500 tractors that was supposed to be in an upcoming auction.

A friend is buying some land in south Georgia west of Gray. He wants a tractor big enough to handle a 5' bush hog. He would like to have 4wd and FEL. What model would yaw recommend? Any dealers in that area?

Was seen on the Cover of a magazine in TSC yesterday. Way to go Chris!

Has anyone heard of a bagger/trac-vac/cyclone rake that can be used on a rear finish mower? I have a Woods RM 48.

A friend has a 2050 that, according to the temp light is running hot. I posted earlier about the water pump. The pump is OK but did have some crud blocking the port to the engine. There is no thermostat and the radiator was boiled out last year. Could the sender for the light be bad...

Need a 18 spline metric yoke that slides on the tractor pto stub. I had one and gave it away. Anyone have one laying around? Most of these were for the reverse pto units.

Can anyone recommed a rebuilder? Local parts houses will not send it off for us to get back.

I need to extend three and install one additional underground gutter drain. A friend is supposed to be coming with a ditchwich to dig the trench. Will be using the black plastic corrugated stuff in a big roll from Lowes. Do I just cover it up with the dirt from the trench?

Is there a way to diagnose if the sender is telling the truth? I know I could plumb in a gauge. Any other suggestions?

My brother picked up some for me yesterday in Rocky Mount, NC for $3.00 each. See at tillerblades.com.

I had a deck built back in the early spring. It is an elevated slab poured on an engineered steel structure. The idea was to have a deck at the main level of the house and a carport under the deck at the basement (walkout) level. Control joints were sawed the day after the pour and a sealer...

I have a 48" 3ph tiller with worn out tines. The plate says its made in USA and is a model 1218. It has 28 tines on it with 4 1/2 in. bolt spacing. Was this made by Howse or Howards or some other company? Would like to get crossover and price some new tines. The brand name on it is Yanmar...