Search results

Are the GPI brand pumps any good? Looking at a factory reman one online for quite a bit cheaper than a new one. Plan on mounting this to an old fuel oil tank.

Figured some of you would like to know there is an accessory plug at the rear of the LX models. Between the right side of the fuel tank and ROPS there is an unused plug that is wired to ignition power. My Ex3200 had this same plug so I believe its for a rear light that I havnt heard anything...

Anyone use 1/4 hose for a toplink over 3/8?" Im leaning to 1/4 for the size and minimal flow it will need, may be a bit of a restriction to slow down its movements. Anyone go this route with success?

Hey guys, got a different tractor and it looks like it may need a shorter top link, not by much though, an inch or two at the most will give me sufficient movement I want. Anyway, I have a hydraulic top link now, however the stroke doesn't use the whole rod end. What I mean is, in its fully...

Hey guys, was somewhat interested in getting some smaller bulk storage of fuel and was wondering what the typical savings would be over going to the station all the time?? We will be using this for on road vehicles as well so it would need to be on road diesel. I was thinking of getting the...

Have a question on an alternate way to fill tires. Wouldn't it be easier to remove the wheel assembly from the tractor, lay it face down with the rim supported slightly by some blocks, pop the upper bead and dump your fluid of choice in with a predetermined amount you want and then re-inflate...

Anyone have one of these that they fill or get filled by a company? We have a rollback wrecker and the tractor to fill every so often and it may be nice to just keep 300gal onsite instead of running to the pump everytime. I can take the tote to a fuel station with the wrecker and slide it off...

Well I'm not dead set on the idea but I look at a box blade and think I could easily use that as a snow pusher without all the attachment points and bracing in the box blade of course. I look up snow pusher prices and am about blown over by them. I could get a box blade, new even, cut out the...

Does anyone have any tricks for lining up NPT fittings (like 90*) fittings where i need them to be, tight and not leaking?

Anyone know where to get hydraulic hose sleeving? I'm talking about the black nylon? type stuff that I can bundle a few hoses together with.

Anyone have any luck cross referencing hydraulic filters for this thing? Looks like there is two for the tractor. I cant find part numbers for the ex3200 or a JD790 anywhere to cross. If anyone can lead the blind I'd appreciate it so I could cross it to hopefully a napa brand or something I...

Hey there, I have an Ex3200 yanmar and have been searching high and low for some answers about adding rear remotes to this thing. I noticed the JD790 is pretty identical to my tractor in everyway and I assume the hydraulics are likely the same. I've read a thread here ...

Taking a look at fitrite's website and I noticed this page with electric controlled remote valves : vavlves I have power beyond on my tractor already and am running a valve for my grapple bucket that I want to remove and just run off a rear remote. I plan on setting up two or three rear...

Ok, let me see if I can explain this, I have two seperate questions in this. 1) I have an Ex3200 with what I found out has the power beyond package installed which ends up with two ports in the back (pressure and return and they have to always be connected). The previous owner ran hoses from...

Anyone copied the "hydraulink" rear top link. Looks just like a double acting cylinder with a valve in the middle to control flow from one end of the piston to the other. Where could I source a ram with the ball/heim type joints that a toplink typically has? That and what kind of valve...

Anyone buy one of these? Looking to replace my top link, didnt want to dive into the hydraulic realm with a valve, hoses and a cylinder but this product looks like it would fit my need. The only thing I'm slighltly hesitant about is the air trapped in the cylinder acting as an absorber, Im...

Anyone ever do something like this? Kubota Quick attach homemade - YouTube Looks pretty straight forward and I have too much tied up in pin on buckets for my tractor already to convert it over to SSQA or anything else. Making sometihng like this would be extremely cheap (couple pins, some...

We have an ex3200 that did not come with quick attach. When we bought it the previous owner used the original bucket and welded tines and a grapple hook setup on it. Since we needed to plow snow as well we bought a bucket for the tractor as well that fit it directly. Now I'd like to look at...

We have a EX3200 with a backblade and an added on valve to control a bucket "thumb" i guess you could call it. There is a "out" hydraulic port near the 3pt hook up as well as a return. The "out" runs to the added on valve and obviously the return runs back through to the return line and port...

Hello, was looking at a used (08) Cubcadet/yanmar Ex3200 the other day and noticed the rear tires were quite a bit skinnier than those found on pictures on the net. Were the tires on the 08 models different than the new(est) ones?