Search results

Thanks Mike. I've got to go through my manuals more thoroughly. Of course the problem is thousands of pages for umpteen models of tractors and I've got to find what's pertinent to mine. :) Or I can just ask my neighbor next time he's over. He's been raising cows for 30 years and has seen a...

I'll keep that in mind! I think there's a Branson dealer not too far from me.

Agreed. I guess it would be illegal to reverse engineer some of these controller boards, but I wish some bright young engineering or computer science student would come out with some type of universal controller board or something that ran on a RaspberryPi that was open source and could replace...

Awesome, thank you everyone. I'll let y'all know what I find when I get a chance to look at it. So what is that little plunger next to the hexagonal fill hole? Is that a dip stick to show the level? I didn't see any markings on it, but I may not have had my glasses on. :) There are also not...

Ford 3400 diesel tractor. I haven't gotten the serial numbers off it yet as to year and design specs, but it has the 6x4 manual transmission. On the top plate where the shifters are, there's a hole with what looks like a dip stick in it. No markings on it or anything and it's not screwed in...

Been meaning to get back in here and update this, but haven't taken the time. Figured I should in case anyone else is having problems. I ended up taking my tractor in to the dealer where I bought it. They kept it for two months and ended up swapping the computer out. I was told they had "2...

Which camera system did you go with Pete? I'm looking for the same setup myself, and trying to find something decent that won't break the bank.

Well..... I *guess* I fixed it. :confused: I poured a couple ounces of this stuff in my fuel tank. Before I fired it up, I remembered reading in another thread where someone said check the vent on the gas cap. I figured what the heck, so I took the gas cap off. It has a little liner that...

My Workmaster 33 has about 750 hours on it. The other day I went to get something from my shed and it was idling and it just shut off. When I got back over there, I cranked it up and throttled up to move on and it died again. It will not run for me. The "engine problem" light comes on when...

I like the boom pole idea, that's what I was thinking on the tractor end with tongs to pick up the log there. I didn't see the hook Plumbstraight..... that looks like a versatile way to go. What I've scrounged to build this out of is some type of ladder material..... I think it was an old...

I'll be starting my log arch build soon and I was wondering.... should I use the leaf springs that are on the axle or take them off? I didn't know if having them on there was a good thing or a bad thing. They have tabs on them where they were cut off an old trailer so they'll be easy to weld...

I'm interested in building a house and shop on some land. I have not contacted the power company yet as I wanted to get some advice on how to route the power into my property and if I have any options available to me. The entrance to my property is funnel shaped with about a 300' road leading...

I have a couple questions regarding adjusting (or maybe repairing) the hydraulics on my 2016 NH Workmaster 33. It has the standard knob to adjust the 3 point hitch speed and I'm familiar with that. But here are my two problems: 1) The lever which operates my 3ph only seems to work from about...

Both my trailer tires were worn out, so I replaced both of them. Old tires were bias ply tires. One of them was really bad and I had put my spare on which was a brand new tire/rim combo I had bought several years ago. The new tires I bought were radials. This is a 6x10 single axle utility...

My land is mostly clay also. So I built some big compost bins. Last year my son and I rode around some of the "nicer" neighborhoods around here looking for leaves for my compost bins because they usually bag their leaves in the "nicer" neighborhoods so all we'd have to do is throw them in the...

My friend gave me a scrape blade and I'm using it to define my roads on my land and start getting crowns established. Because it's a lot of raw land that I've cleared trees on, there are a lot of stumps and unseen roots beneath the surface. Sure enough, I caught the blade on a root and snapped...

Well, I tacked onto an older thread since my question was relevant to that thread and no one answered, so figured I'd start a new thread. It was only since yesterday afternoon, but you guys are usually pretty quick to answer, so I'm not sure how this forum handles the ordering of older threads...

Received my forks and I like them a lot. There's a couple minor bends at the top and it was scratched up on the top, but I don't get worked up by stuff like that. They seem well made and they went on my tractor without any problem at all. Took my son and I less than 5 minutes to get my bucket...

I'm interested in picking up a set of Titan 42" forks for my NH Workmaster 33 with SSQA FEL. I'm guessing I can go with either the Skid Steer attachment or the tractor quick attach and I'll call them about which one, but my question for you guys is, I like the one that has a receiver in it so I...

Zip tied it on today and it worked great. It'll need to be on the back side instead of the front for maximum strength, but I'll have to trim my expanded metal to go around stuff. I agree that a removable piece is the way to go and that's what I'll do. Thanks for all the suggestions!

I have one of the cheap HF flux wire welders and I've only welded a couple things with it with decent results I thought. Now I want to weld a piece of expanded metal on the ROPS bar on my tractor to keep from getting my brains busted out. My questions are, where should I connect my welder's...

I just bought a 2016 New Holland Workmaster 33. It is a diesel and has the tier 4b final exhaust deal on it. I'm reading my manual and it says I need 15W-40 DPF compatible CJ-4 oil. According to the manual, New Holland's is "Ambra Mastergold HSP engine oil SAE 15W-40". Does Walmart sell...