Search results

Yes. The wear looks to be overinflated. Drop the pressure for the type of work you’re doing with the loads normally on the back. Wear should be even across the lugs. A chalk/paint test is a good way to get fast results. Paint or chalk the surface of the lug and see if it wears off evenly. Be...

Personally, I would go with Yanmar

IMHO, you are on the right track as far as the tow behind. With the steep hills you mention, my concern would be with stability of the tow behind while going down hill. Turn limit stops and angle pivot stops would probably need to be fabricated to prevent it from coming around into the side...

Condenser cleaners work well on condensers. Evaporator cleaners aren't for condensers and don't work well for heavy soil, even though they are a foaming cleaner. To answer your question. Yes they do work and are safe. The key is to rinse with water VERY well. Some radiators are horizontal/flat...

Maybe, but this post isn’t about your M9. It’s about another members L4400, that just happens to use the same tire size that one of mine uses.

When replacing the 8-16 on front, I got Carlisle from Amazon and did it myself. Is MUCH easier when you leave the wheel on the tractor. Just use jack stands to keep the axle from pivoting. I searched FB Marketplace for the rears and found 2 new Firestones (14.9-24) from a tire dealer not too far...

Not just one white T, but 2

If I'm on the tractor for a few hours, no problem. It's if I sit at the table for too long I can't walk very well when I'm finally able to stand up.

I have 2 40hp tractors, both with 6' brush mowers. As others have said, you will have to slow down in the taller/thicker stuff. Personally, I set the RPM of the tractor according to the 540 RPM icon/indicator plus about 50-75 rpm with the pto engaged, then match my travel speed to maintain the...

Wash a few times a year. Wax and sometimes WD-40 on black plastic occasionally.

You asked, so my opinion is BushHog and Rhino. Woods apparently makes a great machine also, but I don't have any experience with them. My personal experience is: BushHog is well made and parts are readily available. Rhino is very well made, but parts are typically harder to come by locally(in...

Yep. That's what I said too.

Sounds like the pump to me, but first clean the radiator REAL good. you should be able to get clear water through the radiator coil. Don't use the stream on the spray nozzle, so you don't bend the fins. Personally, I use SimpleGreean and a wand with rating head with a flat spray.

Like others here, I do a good amount of mowing, and these charts are indeed pretty accurate. But you do have to use just a little bit of common sense, and some just don't have that or the natural skill. I sometimes have someone else running one while I'm on another. One guy is a natural, the...

There's an app for that. https://www.landscapecalculator.com/calculators/mow

I just got 2 sets for mine on Amazon. From what I have learned, Yanmar has two different sizes, 10mm and 12mm, referring to the bolts that hold them on.

I have a Titan/Ironcraft. While the Ironcraft/Titan warranty is great, my issue is this, if you need parts you must go through a dealer to get them. Also sometimes the parts they say is what you need, is different that what you have. I ordered new blades through the dealer (with the serial #)...

Sounds like a wire may have come off the ignition switch or broke a wire there while the right panel was off.

My Case Farmall 40 (basically the same tractor) was locked up when I bought it. I got a replacement shock from amazon and with minimal filing, it works great. Now, If you broke any other component (10B-10D), that may be a dealer item. Either way it is worth repairing. You do have to remove the...

Those are all foreign made and comparable, as is almost all scut tractors now. LS and NH are the same. I would pick the closest dealer with the best reputation. For future reference, Tractordata.com is a good source for info., although the website isn't the easiest to get to know. So, Google...

Can't answer on the China/Ebay hoses. I go to NAPA and have them make 'em. That way I know they'll work, and for about the same price.

I don't do excavation. I will do gravel driveways and reconditioning though, so I typically only go down about 2 to 4 inches, if that. I did get into a customer laid gas line once while reconditioning a driveway. It was flex at about 1.5" below grade. He admitted to laying it and had the stuff...

Anybody get tractor seat time withdrawals? Here in the south, we don’t do just a whole lot of snow plowing or blowing and most don’t even have the equipment for that and mowing season ain’t year round. While there are some things to be done, there’s just not a whole lot that requires a tractor...

I've been doing side jobs for several years and even added another tractor recently. I do carry insurance for my tractor side work, but was just curious how others charge for your area. I know some charge by the job or acre, but even that is based on an hourly rate. Being in the Ft. Worth area...

I haven't read ALL of the comments,but have you thought about a boom lift? Some have a 90' reach, can accommodate 3 men and be operated from the basket. Just a possibility https://www.genielift.com/en/aerial-lifts/telescopic-boom-lifts/sx135xc

I get mine online. Amazon or other and mount them myself

Fortunately, my JD dealer, United Ag & Turf is only a mile down the road and they treat me very well. Most folks I know that trade with them seem pleased with the service they get as well.

I recently acquired a 2011CNH Farmall 40 HST with about 1100 hours on it and have been very pleased. I've had to do a few minor repairs, as usual when getting a used tractor, but am impressed with it. Being a "Green" owner/fan for many years, this Farmall has earned our respect. I'm not familiar...

I've done that before. Works very well on aluminum but the plastic ones required good sanding to roughen up the area before it would hold. Also had to drill small holes at each end of the crack to stop the crack from continuing. All that said, I would put a new radiator in it. I wouldn't want...

I bought it new in '04 and it has been a real workhorse and was cheaper than the Kubota of the same size I was looking at. You don't see many of them though, at least from what I've seen.

Only two

We have had a Living Air Classic for several years. They do in fact work. They will also clear a room of smoke in a matter of seconds (personal experience). They are expensive but well worth buying one for long term health advantages. Caution, do not turn the ozone up too high if you are in the...

True, but the OP doesn't state his location.

Here in north central Texas, we use what is called CTB, concrete treated base, in some applications. works very well as it gets very hard and solid before laying asphalt or can be used as is for a good driveway.

You might check out Our Products I put one of these on and am very happy.

Oreilly here told me that if they sell it they have to accept it, so mine goes back to Oreilly and they don't bat an eye. However the 5 gallon rule does apply.

I did a few weeks ago exactly what you are doing or wanting to do. I picked up a 2011 Case 40 for about $4k less than what others are going for. I didn't finance, nor would I finance a used tractor. I hope to retire from my regular job in about 8 years and intend to a add this one to my already...

Does anyone have a website they use for the Farmall D40 tractor. The Case websit is very hard to understand. I registered but my tractor isn’t listed. Thanks y’all

JH:ROFLMAO:

The worst I got into was a 20' stick of 3/8" rebar. Wrapped around the stump jumper. Had my daughter bring me a cuttin torch to the job site. Just didn't have the FEL down low enough.

:ROFLMAO:

Reading other posts about brush mowing with FEL vs. without FEL, got me to thinking of all the stuff that can ruin your day and brush mower. Like several others I do side jobs and usually mow the same places, but still find surprises. Some of the things the FEL has saved my mower from are...

The pressures will change (converge) very quickly when the compressor stops. Short cycling can be caused by a few things. Most common is low charge, but that doesn't seem to be the case here. Some low pressure switches are adjustable (usually a small set screw between the male electrical...

Your terminology plays a big part. "Equipment" trailer vs. "Utility" trailer. Each one comes in many different sizes and load ratings. Typically, a utility trailer can range from a single 1500# axle to two 7500# axles with lengths from 5' to 20'. Whereas equipment trailers, unless a specialty...

Definitely go with the split system with the inverter compressor and variable speed blower. SEER ratings are calculated at full load for a given time. Your system wont run at full capacity probably 95+% of the time, provided that the system is sized correctly

Find someone that is experienced in backing a trailer and has one. A standard 16'x7' to start will be sufficient. Find a big empty parking lot that has good, long stripping. Think school or business. Pull forward and straight with the left tire beside a long line (100+ feet).Using the mirror(s)...

Is the fan shroud still in place? In my younger years, I built and raced Pontiacs (hotrods). While I loved the Ponys, once they were bored, as mine were, they did run a little hotter, more than Chevy or Ford. Any how, when I would test run a new engine, I found that without the shroud, they got...

57” chain drive. Got it used. Works great. Just wandering what brand it is

I would first try J.B. Weld or Steel Stick. Sand and clean the area real good first and you should be good to go.

Things to consider. Dealership fairly close to you for parts/maint. and support. Go with proven manufacturer history, i.e. name brand tractor/equipment- J.D., Kubota, Yanmar (who makes /made most compact J.D.) etc. Now, that being said, there is a new player in the game that I would definitely...

I didn't put a caliper to them, but they appear to be the same diameter

Bucket cylinder on a NH 7309. The cylinder rod pack gland uses a lock wire which I got out by turning the packing gland and pulling the lock wire with no problem, but trying to reinstall the new lock wire has me baffled. There is no hole in the wire groove that would grab the wire and pull it...

Could be either. If the gauge needle has full range of motion, i.e. with key off it goes all the way one direction, then back to the green/red line when key is on, I would start with the sending unit first. Probably easier/cheaper too.

Titan won't sell direct, but most any tractor supply will have one. Also, going through sheer bolts like that, I think I would consider a slip clutch.

"Friend, I wouldn't harm thee for all the world, but thou art standing where I am about to shoot."

This is the one i just put on my canopy support. Replaces the belt holster that was Velcro'd to the support. https://www.amazon.com/dp/B096SGJPWT?psc=1&ref=ppx_yo2ov_dt_b_product_details

Well taken care of tractors without problems are bringing a premium right now. Especially pre-emission tractors. If seller will let buyer run/work said unit for about 1/2 hour or so with no issues, I'd say go for it. It's not what I would consider a "great" deal, but a good, pair price, but it...

1st. thing, 10% to tithing and another 10% just because. God loves a cheerful giver. i'll figure the rest out if it ever happens.

It depends. I assume that since you asked the question, your experience with the tractor is limited, but will increase with time. Is it your property that no one else has access to, where you know there isn't anything to hit, or other? If "other", leave it on and lower it to use as a "feeler"...

Just for reference: In the Ft. Worth area, I charge $65/hr. with a 6' brush cutter and run at 3 mph generally and leave a very nice cut. That is just shy of 2 acres/hr. on level, un-obstructed fields. However, 95% of what I do is NOT level, un-obstructed and the material is generally over 4'...

I thought I would share a solution that worked for me regarding my 990 not charging. Took the alternator apart and cleaned it with a toothbrush (was packed full of dirt). This was a very easy job and may need to be a regular maintenance issue, at least maybe every 200 to 400 hours. This type of...

My 990 did that around 600 hours also. Was the fuel shut off solenoid. On the time delay, it required both coils inside the solenoid to initialize, then only one to keep it engaged, but was sporadic. Before you hit Amazon or the dealer for said solenoid, check the electrical connection closely...

With the exception of the spare truck, Michelin defender LTX MS is the only thing I run. Mine, wifes and daughters

It’s the ones you don’t see that can be costly. Two different times for me.

Power Service products are excellent. Seafoam is good too, but being a local company I may be a little biased. Been using PS for years.

I have the Titan 1606C, and it has been okay. I did have an issue with the gear box u-joint being put in backwards from the dealer. Then the lower seal started leaking. I called them, in Decatur, Tn. and they sent me a whole new drive system. Gearbox, PTO shaft with clutch at no charge. They had...

Sounds like vapor lock. A new fuel pump could be a solution, at least it solved my issue with the same symptoms.

Don't know your plans or what the rest of your yard is like, but our circle drive goes around the the whole house.

Many years ago, before we married, my wifes dad delivered a tractor, pulling his P/U behind, from Lonoke,Ar. to Strawn, Tx.

Doesn't look like it has been abused and in pretty good shape. Check the gearbox oil and for signs of leakage underneath on the output shaft. Note: it is common in some areas of the country to remedy leaking seals with bearing grease. Check that the blades rotate freely and are not bent and are...

I just rebuilt the deck on my 2007 LA130/48" deck. Just a little over $200 with parts from dealer United Ag and Turf. Not hard at all

And I thought I had a honey-do list.

Am I the only one with this problem? When using my iphone, google ads block the bottom of the page, and you cant click on anything there. I can close the ad (after I give a reason), but then the ad place holder still keeps me from clicking anything under it. I can pull the page up to reveal what...

belltec.net

In the process of one myself