Search results

Results 1 to 34 of 34
  1. B

    How much tiller will 2310 handle?

    I reached out and asked if they would ship and sadly they won't :( Finding one of those near Texas has been not been easy
  2. B

    Oil & Fuel New to me YM2500

    So the speed control assembly on mine looks different than what you have. Mine looks like this. If I can't find an appropriate spring then I guess I will bite the bullet and overpay for a single spring. If anyone happens to have their spring out and can take some pictures and measurements...
  3. B

    Oil & Fuel New to me YM2500

    This was very very helpful, I know at least know the OD and the type of spring. I bought a spring variety pack at tractor supply and the have a few flat grounds in there. now to measure them and find one that is .60 to .66 od. On another note, the fuel and poor running issue is finally...
  4. B

    Oil & Fuel New to me YM2500

    So I put everything back together but really wanted to make sure that the linkage was all tight and not going to cause any problems. Well I always thought that the throttle was hard to push and pull so I took it apart to change out the friction disk and check it out. Well of course the ball...
  5. B

    Oil & Fuel New to me YM2500

    So I reached out to Hoye and they were also unsure of where it needs to be so it looks like I am going to be doing what the John Deer 850 post did :-/ its just a pain because there are gaskets in the way etc but will get it done and let ya know how it turns out. I'm also in the process of...
  6. B

    Oil & Fuel New to me YM2500

    Thank you so much for that. I will give it a read and see if there are any insights i can pick up.
  7. B

    Oil & Fuel New to me YM2500

    Yes, he did an amazing job on my pump :-) so I know the pump is good but he was unable to help unfortunately with the markings.. oh well Monday will come soon and I'm sure Hoye had a process on where to line this up.
  8. B

    Oil & Fuel New to me YM2500

    thank you for that info. . looks like I will be making a call to Hoye on monday if I don't find anything out this weekend as this appears to be the exact Pump I have. INJECTOR PUMP --NEW! CH10679 CH10660 OUT OF STOCK
  9. B

    Oil & Fuel New to me YM2500

    :) so the cover that you would have to remove is the one above the fuel pump connected to the crank case vent. I am trying to find more info on this pump as well but no dice.
  10. B

    Oil & Fuel New to me YM2500

    so the part K does not appear to be bent. Is there a different mark on the one for the Japanese side that is to base where the rod should be in relation to the body for governor K link? I think once I figure out where it needs to be it will be easy to get the rest of the parts moving so to speak.
  11. B

    Oil & Fuel New to me YM2500

    No it's the top of the pump. I took the pump out to get a better look and the mark i thought was something turned out to be a speck if dirt. Attached are photos of the pump take out. You can see the shaft has two marks on the rod but i can't make out any other marks to base off of. Also looking...
  12. B

    Oil & Fuel New to me YM2500

    Hi, so my pump does not have those witnesses marks at the end but it does have one next to the post and a line down the middle that i can't get to meet the mark. Here are some photos.
  13. B

    Oil & Fuel New to me YM2500

    long time no update. so I took the governor linkage cover off to inspect and it was LOOSE!!! :-/ but it could have been worse if the little nut fell into the motor so I am thankful to have caught it. Ok so looking at the repair manual it says there is supposed to be a mark on the sliding rail...
  14. B

    Fuel bleeding the 2310 question.

    No worries, I believe someone posted the chart on my chat.
  15. B

    Oil & Fuel New to me YM2500

    So I have a random request, Does anyone happen to have a video of a 3cyl yanmar pressing the accelerator and showing response of it speeding up and slowing down. I know on mine I can press it and there is a significant delay and when I depress there is a delay in deacceleration. Any advise...
  16. B

    Fuel bleeding the 2310 question.

    Thanks for the idea of the seafoam, but quick question on our tractors they recommend 30w is that not the case or do the different models have different weights?
  17. B

    Oil & Fuel New to me YM2500

    So today i was able to bush hog some and it worked well. Oddly when i made a turn the motor would slow down and then pick up speed. On the straights there was no power loss even though I was cutting thru 4ft high weeds, grass, and hard bushy material. I was also able to get it to low idle...
  18. B

    Oil & Fuel New to me YM2500

    Yes absolutely, i picked up a Viton set which is better for the biodiesel. Which is pretty much the norm around here in the diesel pumps. Buna end will apparently swell with biodiesel. So the tractor thru the clear lines i could see bubbles but as i tightened down the clamps the bubbles started...
  19. B

    Oil & Fuel New to me YM2500

    So quick update: I may have figured out the problem. The fuel filter assembly was missing o-rings on the bleeder screws and the fuel shut off lever's o-ring had some flat spots. Going to harbor freight to pick up an o-ring kit and hope there are some that will fit as i can't seem to find the...
  20. B

    Oil & Fuel New to me YM2500

    Hi Peter, I am already using 20% biodiesel and will put in some Opti-Lube. The fuel pump is a fresh rebuild and the injectors are new. Because it runs fine at high rpms I don't think its a fuel starvations issue. So I am left with, governor, throttle linkage, or lines causing minute air...
  21. B

    Oil & Fuel New to me YM2500

    Thank you both.. i am going to make sure there is no air in fuel problems. I have a fuel pump I'm thinking of throwing in to see if that corrects the issue. I'm also wondering if the pinging sound could be an injection pump timing issue so even though it's not smoking i should check that...
  22. B

    Oil & Fuel New to me YM2500

    So I had a bit of time to go out and see if i could get the idle sorted. But can't find the reason. If i drive the tractor around it runs fine but there is not pedal response and or you will hear it surge then drop in rpms. I took a video of me pressing the accelerator and then you can hear it...
  23. B

    Oil & Fuel New to me YM2500

    It did have the idle pretty high, I will get a video of the sound when the idle is lower and what it sounds like when the pedal is pressed. Also yes the exhaust is a bent over no flapper. I do have a PTO Shield and the overrun clutch that need to be installed :D but thank you for the...
  24. B

    Oil & Fuel New to me YM2500

    Here is a video of it running. https://photos.app.goo.gl/f5zvXtXgxvL5pA9F7
  25. B

    Oil & Fuel New to me YM2500

    So this morning I closed every thing up put the filter in etc after letting it drain all night. put fluid in and started it up. So now the 3point works, and the loader with no noises and working smooth. I am going to post a video with it running shortly and hopefully it sounds normal for a...
  26. B

    Oil & Fuel New to me YM2500

    So tonight I did pour clean diesel just to flush the system but did not run the tractor. Couple of gallons then drain and did this till it was coming relatively clear of milkshake. I am leaving the plugs open so that it finishes draining overnight. I will fill with proper fluid in the morning...
  27. B

    Oil & Fuel New to me YM2500

    So I decided tonight to drain the hydraulic fluid and the milk shake did make me sad.. So apparently there is water in the system that i will now have to get out. I did read on some post to put diesel, ATF F, and alcohol into the case and run the tractor but not run the pto etc and I've also...
  28. B

    Oil & Fuel New to me YM2500

    Hi bmaverick so in the first picture you have it's under that metal shield you have. I guess mine did not come with it. Follow the spring. I will try moving the two levers as i was playing with them but could not find any documentation on them. So I was able to put it at 2200 rpms and drive...
  29. B

    Oil & Fuel New to me YM2500

    Ok, thank you for that Winston1 i will take a look and see what I can find out. So another thing I noticed is that the 3point went up but it's not wanting to go back down. I made sure that the lock was turned fully counter clock wise. Does it matter the rpms or should it go down if the tractor...
  30. B

    Oil & Fuel New to me YM2500

    Update: I sent off the pump and injectors to "ThePumpGuySC" his turn around time is incredible. He tested the injectors and they were no bueno so they needed to be purchased. Mike was able to get pump sorted and working and have it back two me in less than two weeks (Most of it shipping time)...
  31. B

    Oil & Fuel New to me YM2500

    Update: So tonight the tractor started up after turning it over for a bit but turns off as if It has no fuel. Thinking it's the pump and will be sending it off to get looked at. Will keep you posted.
  32. B

    Oil & Fuel New to me YM2500

    Thank you everyone for your assistance, so i did check the tractor and was able to turn it over replaced fluids and changed out Fuel lines as well as bleeding the fuel system. So the tractor turns over but it's not wanting to start. I'm not sure if there is enough fuel coming out of the ports...
  33. B

    Oil & Fuel New to me YM2500

    Thank you so much for that info. Is there any particular engine oil you find works better? Also what do you use in the transmission?
  34. B

    Oil & Fuel  New to me YM2500

    Hello everyone, Glad I came across this site as there is Soo much valuable information. I recently purchased a YM2500 that has been sitting outside and not started in almost two years. This being said I'm having it winched on a trailer and brought to my house as i figured it would be best to...
Top