Search results

Congrats on a successful repair!

Reed valve sticky?

Will it continue to run if the fuel tank cap is loosened? Possible plugged cap vent? (Insects, corrosion).

Merry Christmas Y’all!

Home Depot Can’t beat the price vs strength.

Post pictures of the knob! Inquiring Minds want to see!

For my Kioti 5010 I use six two inch straps, each rated at 3333 pounds working load and 10000 pounds breaking strength. Four straps on the frame, one on the front end loader bucket and one on the three point attachment.

I use anti-seize on pivot points that are subject to the elements. It is less prone to washing away and provides a protective coating that resists corrosion.

Hate to say it but the splined shaft may be bent from a previous event.

I have a backhoe (frame mounted) for my Kioti and I like having it on hand for the convenience. It is not difficult to put on. it only takes me about 15 minutes to install or remove if if I’ve done it recently, but if it’s been off for a while, it takes me about 30 minutes just cause I’m...

The Doyle anvil is an excellent value in my opinion.

If the pedals are brought back to neutral with springs, you could put in lighter springs.

Have u been to Federal Iron and Metal in Corpus? They probably have what u want and might sell drops at lower prices. Address: 7414 Leopard St, Corpus Christi, TX 78409 Phone: (361) 882-1777 Email: tadler63@sbcglobal.net Hours of Operation: Sun Closed Mon-Fri 8:00 AM - 5:00 PM

I think copperheads are worse but maybe because I come across more of them.

Search amazon or eBay for a torque multiplier. They are priced around $65 and are well worth the price. They are intended for semi trailer lug nuts but I have used mine for heavy equipment. U just need to be creative about rigging a reaction point for the tool. They can handle 3500 foot pounds.

Brake fluid should be changed out every two years, but not many people do it. I’m guilty…..

Honda civic Will handle everything u specified. Easy to repair if necessary. Great mileage If u need more space: Nissan Rogue

I want one!

A machine shop could make one for you. Michigan Iron and Equipment shows it as available.

Go to YouTube and search ford cab replacement. U won’t think it is scary. No denying It’s a big job but not that scary.

The saskatchewan frost line depth is about six feet (if google is correct). U might check to see that the sea container is sitting on piers otherwise it may move around during the winter/summer cycles causing havoc with your lean-to.

Being a young mechanic back in the 1980s my main objection to metric was the cost of switching to metric hand tools. Fast forward forty years and I have complete sets of imperial and metric! Engineering wise the United States would have been money ahead had we just had the fortitude and...

As much as I hate to admit it; I agree.

I’m reading the dial at 1.9665 which would convert to 49.949mm.

If you have continued use for it on the property, I think this is a great deal. Even if u couldn’t get it to pass PA inspection you could have material delivered and then load it into the bed for distribution around the property.

Pictures please!

By all means jump in to welding with both feet. U won’t regret it. U can start out with a relatively cheap flux core wire welder. If it turns out you don’t care for welding they are easy to sell.

It’s nice to hear of a happy ending! Hopefully two weeks from now you won’t tell us, “He’s baaaaaaack!”

Michigan iron and equipment

The easiest non-kill solution is to staple up some bird netting so they can’t get to the area that they’re pecking on.

You mentioned you have a hydraulic top link on your box blade. Disconnect the hydraulic top link from your remote. The idea being to reduce the amount of hydraulic flow in the system so that the suction side has the least amount of volume to supply during the initial self purging of the air that...

Like others have said, u can be in cold weather and not “feel” cold, but u can be in relatively warm surroundings and feel like you’re freezing. In my teenage years, I became ill with a fever of 106°, and was shivering and could not get warm. I did not think I would make it through the night...

Have u run the snake both ways at the clean out? Meaning that (if the plumbing was installed correctly when the house was constructed) either at the exterior wall of the house or in the crawlspace there are two capped ports into plumbing, one that goes towards the septic tank and another that...

When comparing the same size motors, DC motors will always have more low speed torque than AC motors. Torque is proportional to armature current.

Another option would be a DC motor and controller.

Guard on, plus I wear a full face shield. I guess I’m paranoid!

Got this off the internet for a tecumseh HH160 engine.

I have a large line crossing my property. The pipe developed a leak due to corrosion. Once I discovered the leak the company was very prompt in sending out a team to repair the line.

“Out the front” type I nearly always carry it

26 December 2022, 8:31 pm

I have the inexpensive, negative battery post type.

I have a flex fuel Silverado. The only difference I note between regular gas and e85 is lower miles per gallon.

Always use a wad cutter on armadillos and u won’t have much difficulty killing them.

If there is any question of them using your land find yourself an attorney who specializes in mining and property rights in your state. U will thank yourself later. The mining companies will promise you everything but avoid giving you anything. They will take every liberty they can if you...

Tractor Supply sells them under the Traveller brand.

U don’t want to use roundup? I know it wouldn’t look very nice but it sure would be easy to just spray once a month.

That beats my ring of rocks hands down!

U could easily weave a vinyl mesh (like a lawn chair) which would be light weight and many colors to choose from.

U can also try a fifteen minute soak with Naval Jelly (phosphoric acid). This will tend to dissolve rust and increase clearance between the male/female spline.

I use Tempo dust.

eBay?

I bought some off Amazon in 2019 for $38/gallon. Now I see they are charging $43/gallon (but back ordered). I looked at MSC and they want $82/gallon! Is that right?

That was a grueling trip!

Soft shell crab sandwich especially from lower Maryland.

I use the brand “coop home goods”. They provide additional fill with there pillows so that u can make the pillow as soft or firm as u like.

Could be done with a shouldered bushing. But if u want it done the “right” way, I would weld a bushing in to eliminate maximum pin slop.

Just checked Consumer Reports and they say the best for the following: Solid (opaque) stain: Behr Premium Semi-Transparent : Olympic Elite Advanced Clear Sealer: Thompsons or Behr Premium (Tied)

Another option is to switch over to calcium sulfonate based grease which is quickly taking the place of polyurea.

If you can find it, Mobil polyrex ep2 is also polyurea based and green and would be a very good substitute. I would have no qualms mixing these.

Congratulations!!! [emoji313]

I used an Eaton-Vickers valve that I bought from Surplus Center.

If you search this forum you will find all of the information you need to install your own from components purchased either online or at a local hydraulics store.

My mistake, I bought some on Amazon for my wife’s broken foot a week ago. I just now looked at the box which gives the “stretched” length at 15 feet. Sorry for getting your hopes up.

An ankle brace might be a better option. They are made with several levels of stabilization. But if u have already tried that, Amazon has longer lengths of Ace wrap that can be cut to size. Or join two shorter lengths with the hook and loop ends?

9.62 gpm is what will be available at the max rated rpm.

I’m afflicted with the same disease. I gave up hope long ago for the cure. Every time I try to throw some loose fasteners or extra parts that came with some kit in the trash I get a sick feeling in my gut that is worse than the frustration I feel when my parts drawers won’t close because I...

There is a new alloy for cast called Jupiter Mig that’s supposed be really nice. See YouTube video above. Bear in mind that the person in the video is an accomplished welder. If u don’t do MIG, they also have several varieties of stick rod in the Jupiter family. Just Google “Rockmount Jupiter”

I’d be tempted to replace the entire hard line with a hose.

As long as you use a hose and couplings rated for the pressure, flow, and temperature of the pump it should suffice. I saw a spec sheet online that listed the tym 603 hydraulic pressure at 2000 psi. If I was experimenting with installing a hose I would start out with a braided hose rated at...

Do u mind saying what brand power rake u have and how has it performed as far has durability?

Wrap some scotch brite around a piece of closet hanging dowel to clean the barrel as much as possible Pour some 80 weight gear oil down the barrel and let it soak past the ball. The oil will help seal between the ball and barrel. Then use air again but be careful that ball may come out in a...

Possum or raccoon

I agree that property taxes should be eliminated and replaced with a consumer tax. Also school administrative positions should be cut by 60% and school budgets reduced accordingly. The amount of money wasted in our public schools is a crime in itself. The time I’ve spent tutoring my 16 year...

Check out Hickok45’s video on YouTube. He does pretty thorough reviews.

I misunderstood, I thought you wanted to hook up a cart. Like Diggin it said; the tractor supply county line carryall is roughly $250 and I don’t think u would save much money trying to fabricate one given the cost of steel and welding rod. I have one and find it very useful. And yes the...

I’m not familiar with this particular tractor; but doesn’t it have a drawbar?

Macnaught not Mcnaught. Hopefully our Irish and Scottish kin don’t get too upset [emoji4].

If you have a generator regulator take the B terminal wires off the regulator and connect them together (thus bypassing the regulator) and then try and start with the key if it starts right up your generator regulator has an internal fault.

Hydrogen Peroxide works well on all biological material. DO NOT MIX peroxide and bleach as pure oxygen is produced and an explosion could result. If you can get to the condenser coil and vacuum away the lint and dust that build up over time; this material may have absorbed odor. Wear gloves if...

3F is Fontana Luigi

$7.39 for a 5 lb whole chicken

I use the tire treads shedded from semi-trailers I find on the side of the road. I cut them to size with a portaband saw and mount them with bailing wire.

That’s not aggressive, that’s brilliant!!!

I’m not saying that this diagram is correct but see if it makes sense by following your wire’s. It comes from a switch for sale on Amazon

I’m a fan a James Hardie products.

I am a very light user and I grease every three months to avoid the aforementioned drying of the grease. The exception to my normal schedule is the backhoe which I grease every time I use it in addition to every three months.

I’ve put pins in the hole and then an air hammer against the pin

Have u checked the air filter?

Go to a local machine shop. They can build up the holes with TIG weld and then re-drill the bolt hole pattern on a mill.

I’ve never had an aluminum crimp fail. I have had hogs run through fence lines and break the wire but the crimps always hold.

She paid for two months at $15/month. We had no problem ending the subscription.

Go online and get a Chegg account. My wife just finished a statistics course and Chegg is fantastic. Also Minitab software is very helpful.

Oddly, satisfying to watch!

Bifen IT. Mix 1 oz per gallon of water. About a half gallon of the mix per mound. Bifen is a “persistent” insecticide so as long as it doesn’t rain too much it will continue to be effective for a month or two.

Practical, inexpensive, I like it!

Sounds like a carburetor main jet blockage. Remove the bowl and take a piece of fishing line or a coarse bristle from a paint brush or a thin copper strand from a length of wire and gently push it through the jet orifice. Sometimes the jet must be removed to get to a metering tube to clean it...

A piston seal failure would make for a very bad day!

One method for troubleshooting diesel starting issues is to buy an inexpensive RPM tester. Diesel engines require about 200 rpm for reliable starting. Even when the engine sounds like it is spinning fast enough, it is difficult to tell whether it is, if you don’t have a tester. In cold...

In threatening weather do you turn the panels upright to mitigate hail damage?

This is the type of system I use. Very easy to setup and economical. Any old computer display or small flat tv can be connected to it. Search Amazon for various brands and numbers of cameras desired . The resolution of the cameras is not tremendous but good enough to monitor porch activity...

If a sufficient amount of water gets into the tank, bacteria and fungi can proliferate in the water while using the diesel as a food source. Waste biproducts from the microbial activity form a sludge that will clog filters. You’ve probably heard the phrase “keep your powder dry”. In tractor...

Beef tenderloin

Check to see if you have at least 12.4 volts at the battery. If so, bypass the ignition switch by going direct to starter solenoid with a pair of jumper cables. The starter should turn unless there’s a solenoid issue. When doing this make sure the transmission is in neutral.

It depends upon how much it bothers you that there is a leak. It would weigh on my mind a lot; but for others a small leak is not a priority. Functionally, no u need not be concerned. Cosmetically, and system wise you have a low priority issue that can exist for years without significant...

Here is a link to a manual. Be patient, it takes about 20 minutes to open the file and then another 20 minutes to save it to your computer. But it’s well worth the effort. Http://www.demss.co.kr/dossfile/manualnew/WM/CK2610,CK3510,4010_WM_170123.pdf

The pto system on the early Ferguson and Ford tractors was not “live”. In order to have hydraulics u must have the pto engaged. When using a ground implement that is attached to the three-point u do not need to have the pto engaged. If u hit a hard spot that causes the rear wheels to start...

These four YouTube channels I found to be very informative. MrPete222 Frank Hoose H&W Machine Repair and Rebuilding Joe Pieczynski I started out on the journey u are about to begin roughly six years ago and I’ve enjoyed every minute. Here are some thoughts: A mill and a lathe are...

TO 35. Is it gas or diesel?

That’s pretty cool! No pun intended.

Put some penetrating oil on it and let it sit a few days. Take a dremel ( or similar tool) with a rotary burr and grind the threads down on two sides to make wrenching flats.

Whether you stop or not, I won’t judge you.

It can be reclaimed. Are u near a municipality that would want it? Of course u would need to allow their heavy equipment on ur property.

I have a 2485 backhoe and do not have any interference. As a previous poster mentioned there must be an incorrect assembly.

I know it’s a bit of a drive from Tyler but call Lowery Wholesale in Paradise, and see if they have it. 940-969-2527 3407 TX-114 Paradise, TX 76073 Hours M-F | 7:30AM to 4:30PM Sat | 8:00AM to 11:00AM Sun | Closed

A flat tax would shrink the size of the IRS and eliminate tax cheats, but simple solutions are not in the best interest of the government bureaucracy.

I read your first post the responses were not offensive. I can’t figure why it was locked. Like any government organization the power and funding goes towards making the organization more powerful and needing more funding.

Tire seal from Texas Refinery Company https://www.texasrefinery.com/products/specialty-products/tireseal/

U might be able to stop the leak with just a little sealant.

Pathfinder AT. They are Discount Tire brand competitors to BFGoodrich

Tongue weight applies to how the weight on the trailer is balanced. Tongue weight does not effect the load capacity of the trailer.

I have a nx5010 which I believe uses the same industrial rim. The dimension is 9 1/2 inches center to center.

My NX5010 has had 3 regens in about 400 hours.

Be glad your wife is around to make work for you!

I think you would be money ahead by doing something like this guy did on his ym2000.

Do you know anyone with a lathe that will turn down the new studs for you?

Excellent summary, Sir!

We need a video of that marvel in action!!

Shoot one or two and the rest will get the message.

The answer lies in gradual reduction of air pressure and a test drive to see how it feels. Since u have no loader on front I’m thinking you could easily go down to 8 psi on the front. For the back try it at 14 psi with the mower both lowered and raised. My concern with the back and too low...

U shouldn’t paint radiators because u get the most efficient heat transfer with the bare metal. But if u must; use an aluminized type paint such as applied to exhaust manifolds.

I just stepped on a dead wasp that I must have drug in on my shoe and got caught on my indoor floormat. I’m here to say that the onion juice does actually work. The pain is not all gone but it’s not increasing anymore and the swelling is subsiding. Thanks to the poster who mentioned this...

I’d start out spending the money for a six foot box blade then try doing one acre at a time. The technique is to drive figure-eights within the chosen acre, pivoting the figure-eight about the center of acre. If u feel you’re making progress and get the hang of it; continue on to the next acre...

If it idles but won’t accelerate, unscrew the main jet and run a thin brass wire, aluminum wire or a bristle from a brush through the jet to clear any gunk. If worried about damaging the jet during removal just leave it in and carefully clear it.

I have a soft spot for most reptiles and amphibians; but I’ve never found love for snapping turtles, copperheads and rattle snakes.

The lumber would be worth something!

I think pic 2 is Bush Honeysuckle

Have u considered a shipping container?

Cell phone tower?

I just thought it was a typical typo u see in some of these descriptions from certain countries. It would more likely be 10-30 amps on a 12 volt system. Or maybe they’re referring to an equivalent cold cranking amp capacity. In any case these emergency jumper products really work well (even the...

[emoji106][emoji106][emoji106]

Legality-wise check ur state laws. For instance, in my state, the maximum overhang allowed is four feet past the trailer end. You may also want to measure the tongue weight just to be sure u have enough with that particular placement.

It sounds like fluid ( most likely hydraulic) momentarily leaking past a seal. Since the sound dissipates so quickly, I wouldn’t worry about it. I would guess that it is an o-ring that was either twisted upon installation or perhaps slightly cut and it allows leakage until pressure builds up...

NH TC40A Starting problem https://www.tractorbynet.com/forums/index.php?threads/NH-TC40A-Starting-problem.439759/ Check out this thread as well

Congrats!! You will appreciate the convenience of having that work horse!!

Two areas I would look at are 1) battery circuit corrosion. Check battery posts for corrosion and follow the cables to the alternator and frame and check for corrosion there as well. 2) solenoids. Many tractors have engine cutoff and start solenoids that can begin to fail intermittently...

Www.archives.gov

In Texas, if the land has an agricultural valuation and is fenced; climbing over a fence is a class B misdemeanor, if u climb over with a firearm it is a felony.

When the cylinder is extended place a piece of 3/16 angle iron, cut to length, over the piston rod (tie wrap in place).

I just charge the battery when I need it or replace if necessary. I freely admit negligence regarding the backup battery. I am far more conscientious when it comes to my safety chains. In my mind the chains are “an ounce of prevention”, and if some event occurs where the chains come into play...

Since the joint is good; cut up an old inner tube, wrap it around the joint and safety wire in place.

If tinhack has an adjustable three jaw or a four jaw chuck then it will be possible to resize the bore.

The image is kind of blurry but it could also be a cotter ring. If you find any clevis pins laying around you’ll know why!

I hope you don’t have pine beetles (weevils).

I was thinking sinkhole.

No muss no fuss

Use on any surface bare metal or painted.

A modern fire truck pumps water at the rate of 1500 gallons per minute. So u will get about 1 minute 20 seconds of fire fighting from a 2000 gallon tank. Just something to consider. Do you enjoy swimming pools? An above ground 21 foot round pool is about 10,000 gallons and it would serve a dual...

What do you get when you cross a Segway with a drone….?

Bifen is the best!!!

Check at the brake pedal where the cancel switch contacts the pedal. Some of the Asian carmakers have a rubber plug or hard plastic stop on the pedal that as it wears it will break the contact simulating a “cancel”. Maybe with temperature changes the shrinkage/expansion of the material is just...

Vortex is a wood miser brand as far as I know; it is a specialized blade for sawdust removal. Timberwolf speaks to sawdust removal in their guide and mentions around 80% sawdust removal as being ideal to allow cooling of the blade during the cut. I’m not an expert by any means but in general...

I like Timberwolf. https://timberwolfbandmillblades.com/

Your nearest LS dealership should be able to help.

Wow! That is customer service that is above and beyond. I would have been satisfied with $50 off.

I’ve used my 72” ratchet rake to spread and level a gravel base for a 40 foot shipping container and it did that job very well. I can’t speak to working on a slope; but now that I have seen Jeff’s pictures of grooming a fire break I am now interested on trying mine on my fire pit that has...

Put all terrain tires on the truck and u won’t get stuck in wet grass.

9.6 GPM at 2600 rpm at either coupling.

Very nice machine. Kinda sad though that the fellow u got it from didn’t get the chance to see it run again…

These digital copies are well worth having since the photos are in color. The workshop manual I bought from my dealer is printed in black and white and sometimes it is difficult to understand what is being shown because of all the gray tones.

From the picture you posted it’s not a 9N it’s an 8N. I’d say it’s worth it but only because I love old tractors. As others have already said, if u enjoy restoration and have the time and space u will have some fun.

A quick check for intra cylinder (bad cylinder piston seals) leakage is to raise the boom, stick and bucket, shut off the machine and see if either boom, stick or bucket bleed down. I noticed the bucket cylinder missing in the picture maybe you’ve already done all those checks.

I would start by plumbing a pressure gauge into the system and see what the pump is putting out.

Like you I have never had this unit apart and I am just guessing but from the drawings it looks like the spring is a centering spring so that the spool returns to a neutral position. I would guess that when you remove the the pivot box this spring does not have much if any compression on it...

Many air handler blower motors have low, medium and high settings that are controlled via a switch or “speed wires” (located at the blower, not the thermostat) that can be connected depending upon the season. Your installer should not object to testing fan speeds for you to find the most...

How many btu is the unit? It might be that ur unit is oversized for the room. But u can google sizing of heat pumps and do the calculations yourself to determine if that is the case.

If the gearshift boot is old and the tractor is kept outside, water will migrate into the case.

Yes, it takes the place of a cartridge in the chamber and lets you know the gun is in a safe condition.

The yellow piece looks like a chamber flag.

I use NLGI 000 in my bush hog and my post hole digger gear boxes. U can purchase on eBay for about $85 for 35 pounds.

Damn! Maybe a little angle grinder on that sharp point! Did u need a stitch?

Damn! Maybe a little angle grinder on that sharp point! Did u need a stitch?

I operate with a cab in the woods frequently. When I do, I have a pole saw with me to deal with any low limbs.

I have been very impressed by the Home Depot Husky brand tool cabinets. They are well priced, midgrade, with fully supported ball bearing drawers and have many different configurations and sizes. Some also have built-in power strips which I find very convenient. I own the 46” and 52” 9 drawer...

Take this for what its worth (its worth nothing its just my opinion); my research on Universal Tractor Hydraulic Fluid (UTHF) leads me to believe that the over arching specification for UTHF is the John Deere JDM J20C formula. If the UTHF fluid you are using states that it is recommended for...

An HD 10 requires 12 GPM hydraulic flow for optimal performance. The DK4510 I believe, only produces 9.6 GPM on the implement side of the pump at 2600 engine rpm. Before you start buying or renting equipment, it may be beneficial to put on paper a cost-benefit analysis of doing the work...

This is a fairly simple shaft to have machined if other sources can not provide. Just a guess at cost is about $25 for material (assuming 24 inches of 1 5/8 1018 round bar). 3 hours shop time at $110/hr. So between $350 - $400 at a local shop.

LittleBill, How did you tolerance the parts so that they had a snug fit? Did you use something like - .002 for the cover inner diameter so that it fit snugly or is there another method? Just curious. I’ve thought about getting a 3D printer but haven’t mustered the courage yet!

I like the MIE ripper. It also serves as a trencher.

64 1/2 Mustang 66 Oldsmobile F85 cutlass 73 Ford E300 work van with 3 on the tree 1977 Suzuki GS 750 73 Buick Electra Limited 81 Datsun 510 72 Chevelle Concourse Estate wagon 89 Honda Civic SI hatchback 96 Honda Civic EX 1986 Ford F-150 XLT extended cab 1996 Ford F150 extended cab 1997...

If the tool has been properly lubed and had decently clean air throughout its life three o-rings will usually put it back to as new condition. Sometimes the rotor blades need to be replaced.

If nothing else u no longer need to worry (not that u would) about 5G compatibility...

Looks great! Years of enjoyment lie ahead!

I would make some aluminum or brass shims to slowly separate the housing. Similar to the screwdriver method but more refined.

It may differ by model tractor; but for instance my NX5010 HST takes 45 Liters of hydraulic fluid. Kioti calls out several brands but mobile 424 is a common fluid.

Never use stainless bolts with stainless nuts. Use plain steel nuts with stainless bolts.

If you will be doing a lot of thin gauge work in the future, invest in TIG. Or just keep on keeping on with what ur doing but try some aluminum heat sinks near the weld ( of course success will be limited when trying to close up a cylinder shaped object like a muffler).

U mentioned a cultipacker was used. Was a harrow rake used to provide a final smoothing of the ground ?

There are quite a few diagrams in the shop manual. What circuit are you looking for?

Did u happen to replace the gas tank cap? It should be a vented cap.

When I’m hauling just the trailer (tongue wt about 200 lbs) I don’t use the WDH. But when I’m hauling the tractor the tongue wt increases above 600 lbs which is limit of my receiver. I always use the WDH when hauling the tractor.