Search results

Had a coolant hose come loose which set ofF the CEL. Reattached hose, filled coolant and now still have the CEL. Anyone know how to turn it off without the dealer?

My NX4510 has 2 rear remotes. Neither has the float function. Can I run a backhoe from these remotes that don't have float function?

Has anyone put wheel weights on their NX? Does Kioti make them?

I have a 2016 Kioti NX4510 with 2 remote valves. Bottom one is hooked up to hydraulic top link. Top one is used for a rear blade or recently an old home made dump trailer. There is a vent hose on the valve body that spews out hydraulic oil when I lower the dump trailer. This does not happen...

Not sure if anyone else has had this problem. In cold weather PCV valve freezing shut. Happened when I first bought the tractor 2 years ago. Blew out dipstick, but also blew out main oil seal on crank. Had to split tractor to replace. $5k in labour 😳😳. Luckily on warranty. Happened...

kioti manuals have many omissions and discrepancies. On my NX owners manual, on inside cover, it says to replace engine oil and filter every 100 hrs. In part 7 under maintenance, it states tier 3 engine oil every 200 hrs or every year. Tier 4 every 200 hours. No mention of annual for tier...

Looking for any experience in cleaning a DPF. I had a bad injector, and DPF was regenerating every 3 hours. Had bad injector replaced, and now regenerates every 10 hours or so. Previously could go 30 to 40 hours between regens. Am thinking DPF needs a cleaning? I have read you can power...

Have 330 hours on tractor. Regens every 50 hours give or take since new. About 12 hours ago started to regen every 3 hours. 2 auto regens and 2 manual regens. At beginning of last manual regen CEL came on, regen stopped and went into limp. Searching other threads leads me to believe a bad...

Am not very impressed with the radio or speakers in the NX. Has anyone upgraded to something better? Did you have any problems hooking up a new receiver? I am guessing speakers would be an easy upgrade. Any input would be appreciated.

It has been pretty cold here lately in Western Canada. Today, engine blew out crankcase dipstick due to high pressure. I am assuming that a vent hose is frozen. Anyone else see this happen to them?

As a Canadian, we have to put up with months of below zero weather. I push lots of snow, and am thinking of adding an adhesive oil pan heater to my hydraulic sump near the rear axle. I already have a block heater that does well to heat the engine and engine oil, but it takes some time to heat...

As a Canadian, we have to put up with months of below zero weather. I push lots of snow, and am thinking of adding an adhesive oil pan heater to my hydraulic sump near the rear axle. I already have a block heater that does well to heat the engine and engine oil, but it takes some time to heat...

The A/C on my 2016 NX will 'flicker' on and off. The problem seems intermittent. Dealer came and looked at it, and it behaved when he was looking at it. Only after he left did it start acting up. High and low side pressure seemed ok. Screens are completely clear of debris. When it works...

I have added a hydraulic top link on my NX4510. Today, after box blading for an hour or so, the rear remotes were extremely hot. The hydraulic top link was only warm. Could I have this hooked up wrong, or is this 'normal'? Neither remote has a detent.

Was tired of getting front flats on B7800. Had front tires foam filled. I think the tires were overfilled. Tire tread now rounded and there is no give. I've been having driveline trouble since. I have broken front u-joint on shaft. When in 4wd there is "tension" in driveline. I think...

Has anyone replaced the front drive shaft on a B7800 without splitting the tractor? My 7800 shaft broke at the u-joint right at the transmission. Want to replace, but don't want to split the tractor. Can this be done, or am I in for a big time job?

Noticed today my 2016 NX4510 with only 65 hours leaking oil from tab on bottom of starter motor. :mad: Only leaks when engine running. Think it can only be rear main seal???? Not very happy as it will probably require tractor split in half. Anyone else ever experience this? I just...

Noticed today oil dripping from plastic tab on bottom of starter motor. Only drips when engine running. NX4510 with only 65 hours on it. Afraid it is the rear main seal leaking. Anyone else have this issue?