Recent content by dweitzel

  1. dweitzel

    To bond or not to bond neutral and ground in new electric service panel?

    My question is the bonding screw between the ground bar and neutral bar always required in a new, stand alone entrance service panel? This is not a sub-panel, nor will I be installing a sub-panel. I have installed a Square D, 200 amp, QO panel and need to know if I need to install the green...
  2. dweitzel

    Posthole Digger  Anyone rent rock auger bits for skidsteers

    Anyone know of anyone in SW Ohio that rents rock auger bits for skidsteers. I know a bit off topic, but I need to get the last 10 holes or so drilled before the weather turns for a section of fence. I have a 12" PHD for a 3-point rear PHD, but it looks like the rock bits require down pressure...
  3. dweitzel

    Need tooth adapter 4K1690 for Caterpillar 933F

    Snapped a tooth off my bucket of my Cat 933F. The serial number is 42A342 and I believe I have the standard bucket IK8358. Anybody have one they would part with? Or know of a bone yard that I could try to source the part from? Thanks. Striking out. Original part number is 2K4680 and had Cat...
  4. dweitzel

    7360ss filters list

    Thought I'd post a list of filters (air/oil) that I've crossed over for my 1999 7360ss cub. This has the 4 cyl Mitsubushi 36 hp engine in it. Not had to do much to this but glow plugs, and the controller that usually burns them out. Good machine and believe it or not, used it for the last 2...
  5. dweitzel

    7360ss water temp sensor?

    Fighting glow plug issues again. About 40 degrees this morning. 12 volts is only supplied to the plug for less than one second and the light goes out and the voltage stops. I want to check the water temp sensor and it appears there are two in the thermostat housing. One is probably for the temp...
  6. dweitzel

    Loader  Case LX132 cable broke at joystick

    My neighbor has a LX132 loader on his Case tractor. He broke the adjusting sleeve at the joystick and I can't locate just the adjusting sleeve, but it looks like it may be in a kit, part number 87415531. The kit itself is called a Cable connection kit. Does anyone have an idea where to get just...
  7. dweitzel

    Oil & Fuel  Need part number for MF 135 Diesel fuel sending unit

    I've looked on the agco site and can only find a part number for the gas engine. Anyone know if the same fuel sending unit for the gas work for the diesel? Are the fuel tanks the same? My massey ferguson 135 is a 1971 sn 9AII5526
  8. dweitzel

    Positioning new barn in relation to wind?

    Getting ready to start a barn project this spring and wondering what is the best way to position the barn in relation to the wind direction. I'm on top of a ridge that sees some pretty hefty winds. Pole barn 27' wide by 64' long, 18' side walls. I'm thinking about positioning the corner of the...
  9. dweitzel

    Sprayer  Rust removal from inside sprayer tank

    I recently purchased a JD 29A, 110 gallon pull behind sprayer, but the inside of the tank has a coating of surface rust. I'm afraid that just using a in tank or aux external filter will just clog up. Anyone know what I can clean the inside with and re-coat with to keep the rust in check? I...
  10. dweitzel

    Bought a $146.91 hydraulic filter today!

    Yep, that's right. The hydraulic filter was $146.91 and 12 quarts of oil were $148.50. Grand total with tax for a fluid change at 230 hours $313.59. How in the world can Mitsubitshi and Cub even look customers in the face and charge $146.91 for a FILTER? Anyone had any luck crossing this...
  11. dweitzel

    Sickle Bar  How much tractor needed for JD 350 - 9' sickle mower?

    I have a Cub Cadet 7360ss, Mitshubishi 36 hp diesel, 4x4 , weighing 4500-5000 lbs with the weighted tires and FEL installed. Will this run a John Deere model 350 9' sickle bar mower? I just need to know if the HP is in the range needed. I posted a question over on Yesterday's Tractor forum a...
  12. dweitzel

    Sickle Bar  Will John Deere 350 9' sickle mower fit and operate on a Kubota L3400

    Will John Deere JD 350 9' sickle mower fit and operate on a Kubota L3400's 3-point lift arms and clear the top link assembly? I have a Cub Cadet 7360ss which is pretty comparable in size to the above Kubota. Most people are familar with the Kubota and not the Cub series, so that's why I asked...
  13. dweitzel

    Just finished up the JD KBA 10' disc!

    Just finished up the repairs on the John Deere KBA 10' disc. Can't wait to try it out. I needed to make a few improvements for my Cub Cadet 7360ss to work since I do not have rear remotes to operate the cylinder. I guess I took it a little further than I wanted to, but once I started snapping...
  14. dweitzel

    Anyone with a KBA 10' JD disk? Help w/Pics

    I finally found a JD 195? KBA 10' wide disk. Needs a little work. Anyone have one that can send me a few pics and take some measurments of the rear threaded rods that hold the rear discs from moving side to side? I need to fabricate a couple of new parts and remove a couple pieces of welded on...
  15. dweitzel

    How wide of a disc can I pull?

    I need to purchase a disc. How wide of a disc can I pull with a 36hp Cub Cadet 7360ss 4wd, with a Mitsubitshi diesel in it. Does it make a difference in width if I go with a 3 point disc, or a pull behind other than not having remote hydraulics to raise and lower a pull behind and the lift limit...
Top