shuttle

I've got a 2665 with just under 300 hrs on it. The shuttle shift is extremely clunky- you have to fight it to engage, sometime it misses and grinds horribly. I've found double clutching helps to get it into gear, but it is horrible compared to my previous shuttle, a 2655, which was very smooth...

Hi all- First post in many years... I'm looking to replace an old Case/IH 385 that I use primarily for pulling 7ft finish mower. It's been great at that task, but it's almost 40 years old and the list of problems is growing, parts are hard to source, etc... Given that I use it primarily for...

Within the past 2 weeks my shuttle shift has been more difficult to go into gear, both directions; so difficult now my left hand center knuckle is swollen and i cannot straighten the finger. Any member have a cause and solution for the shifting difficulty?

POSTING FOR A FRIEND. This is all I know about it. Alabama, Kubota 3130 4x4 with FEL, shuttle shift. 2300 hrs. hes the 2nd owner. No issues, works good. hes asking $13,750. If interested or have questions Pm me your # and i will pass it on to him to call you directly.

Is it rue that a 2013 3616 has DOC not REGEN? Plus the shuttle is true gear on gear with no clutch per say? See one with 700hrs foe 12,500. thoughts?

Adjusting shuttle response not on top dial rabbit and tortoise but the 3 adjustment knobs below, i cant get the response i want with the top adjustment knob and wanted to see if anyone knows the procedure to decrease the slamming into gear as you move from reverse to forward Top knob all the way...

I’ve got an older 3016 shuttle with no reverse. Figured by the time I remove trans & replace problem, it might be easier to replace trans. If I can find one reasonable. Also I like have a book Manual Any help with my No reverse would be appreciated Thanks Hal Woodville Tx 75979

Hello! I recently bought a 1994 Kubota L4350 Hydraulic Shuttle Everclutch. It runs and operates well, except for one thing. The hydraulic shuttle lever is sloppy when put into forward gear. When put into reverse, the lever "clicks" into place and reverse gears work as expected. The lever stays...

Shuttle will not go into reverse, fwd works Ok. From under tractor, I can hear reverse click as if going into position, just as same clicking into position in fwd. I feel I must split tractor to find problem. Hope someone can give some insite And step by steps to split tractor Thanks in...

Got rk 37 sc shuttle shift won't move in 2 wheel drive no noise bang or nothing I put it in 4 wheel drive and front wheels will pull

After replacing a sync reverser and now have lost 2 gears I want a compact utility tractor with a wet clutch and power reverser. Don't want hydrostatic. Most of the Korean, Japanese and Indian tractors I have researched use a dry clutch and a sync reverser. Is there a specific brand that uses...

Kioti px1052 has severe shuttle shift engagement with no one knows how to repair? 500 hours on clock

Rather than than tax my 70 year old addled brain and figure it out by myself, would anyone be kind enough to tell/show me where the Neutral safety switch location on my Max28 8x 8 is? A .pdf from service manual would be a great help, plus the part number. Jiggling the forward/reverser handle no...

This tractor is a 2016 model Not even enough power to pull itself up a hill . Wondering if anyone has had a similar problem?

I have a 1736 with a cab and it has the 12 gear shuttle shift. Just recently i noticed that when i shift from forward to reverse (yes, i am moving slow), i get a hard jerk. It happens both ways - going into forward and reverse. I have no issues manually clutching and moving the shuttle shifter...

Hello, Hopefully someone can help me with an issue I'm having with my tractor. I have a 2018 mahindra 1526 shuttle shift. The forward & reverse selector has become extremely hard to move from forward to reverse some times it wont even do it. Last time i used the tractor it seemed like once i got...

Hello All, I just recently purchased a 2007 Branson 3510(I) shuttle shift, and am worried about how loose the shuttle shift lever is. I don't have any issues with it going in and out of reverse, but I have to hold the lever in the middle of the column for it to shift. Once I let loose of the...

Anyone ever experience a dealer/servicer recommend to not change the hydraulic oil in a shuttle shift? They said they only recommend changing if it looks milky because there isn't anything wrong with it. I've been debating on sending the oil off to be analyzed, but I don't know where to send...

So we have about 15ish acres of New England field to mow - alot of it is a bit on a hill- I just found a 2022 LS MT345E with 85 hours on it- It is a synchro shuttle with R1 tires- Since 85% of what it will be used for is mowing the fields I do not think I will miss having the rear remotes- I can...

Hi i'm sure this has been brought up before but i've not been able to find it. Our tractor has been sitting for the winter into summor and just now been able to get it running. But when I shifted into gear and let the clutch out. Nothing happens. Although if I push forward on the gear selector...

Seems a little late for me to ask (2012 unit with over 2000hrs all by me) but am I not supposed to use the foot clutch to do close work like loading bales with a grapple etc? Early on I tried to use the throttle and brake to feather things but just not enough finesse there IMO. Am I doing this...

I have a XR4145 that I've been abusing for about 7 yrs. Been doing fair amount of maintenace as required. Recently my Fwd/Rvrs is getting stuck when I shift. I'm at a stop, clutch is in. I go to shift and the handle just flexes. After I rock back or forth it will release and I can shift. What...

Was mowing and stopped to back up and shuttle shifter went in to reverse just fine and backed up. When I tried to shift back to forward the shifter wouldn’t move. I can go in reverse just fine. Changed hydraulic filter and there was quite a sediment buildup on the screen going out of the filter...

has anyone ever had this issue

I was attempting to tighten up my shuttle shifter , an mistakenly pulled the whole rod free of the lower workings. And now I can't see what I'm doing since the plastic Dash /cowl assembly is in the way .. Of course i in the middle of Rototilling season ,, and have a busy week of so a head of me...

took out of barn today and after it warmed up, the Power shuttle high/low alarm light would blink red. it would blink 3-4 real quick then do a steady 4 then a steady 9, I assume that is a code 49? anyone help with this?

Hi all, hope one of you can help me. I have a 1994 555D Ford backhoe and when I have been using it anywhere from 20-30 min the shuttle shifter stops working and it won’t go forward or reverse. After it cools down it can be used again…. What is causing this? It’s a real pain and can’t get much...

Hello I am trying to fix a "PTO popping out of gear" issue whereby the PTO will stop spinning as the lever kicks back to "off" If I hold the PTO lever down it will stay engaged, but I can't seem to adjust the lever detents so that they will hold. I am about to remove the linkage housing so I...