Search results

I have a CT335 that I'm actually quite happy with. However this winter we've had an extraordinary amount of snow and I'm finding the CT335 is having a hard time pushing it and lifting it to the full height of the snow piles. I've come across a CT450 for sale and I'm wondering if the extra hp as...

I have a CT335 with HST drive and have noticed a few times when I disengage the the front wheel drive that it doesn't always fully disengage until I move forward a distance. Then it in disengages with a noticeable clunk. Has anyone else experienced this issue and if so what was involved in...

I was performing the first 100 hr oil and filter change on my CT335 after the initial 50 hr service (dealer did this service) and had the following occur. I noticed that the filter was on very tight and it took quite a bit of force to get it to move at first. However it wasn't the filter moving...

I've been looking for a grapple for my Bobcat CT335 tractor and came across these grapples made by ANBO for compact tractors. ANBO Manufacturing - Rock, Root & Tree Grapple GR-M I was wondering if anyone out there has had any experience with these units. I noticed that their weight is quite a...

I was asked in another thread to post some pictures of my CT335 with cab. I know when I was considering purchasing this tractor it was very hard to find any pictures of a CT335 with a cab. Having plowed snow and snow blowed it on a tractor without a cab I new I wanted a cab on the next tractor I...

I went out to use my CT335 today and noticed that areas of the FEL were covered in yellow markings. My first impression was that it was an spray of oil droplets on the tractor, but after close examination I realized it was surface rust breaking through the paint. The tractor is less than 3...

I need some information on the Wallenstein GX720 3pt. backhoe. Most forums seem to make a point, of saying "stay away from 3pt. hitch backhoes" because they seem to break the 3pt. hitch. However when I've gone looking for documented evidence that this actually occurs I'm just not having much...

When I purchased my CT335 with cab I thought I had researched everything about this model and asked the dealer all the right questions. I ordered the unit on the thought I might want to put a BobCat backhoe on it at some future time. So the dealer advised me that installing a detente in the rear...

I noticed in the CT335 operators manual that it states that foam filled tires are not approved for use on this tractor and will void your warranty. It does allow calcium filling of the tires though. I'm curious to know what the issue with foam filling is. My dealer didn't know. Does anyone have...

I received my new CT335 this week just as the temperature decided to drop down to -30C. The unit is equipped with, block heater, battery blanket and oil pan heater. I decided to try it out once the temp rose to -25c after being plugged in for several hours. It started no problem but I was...

I was wondering if anyone has had any experience with a Chinese made backhoe, produced by a company called Hanmey. They appear to be mounted on the 3pt hitch (no sub frame) and use a PTO driven hydraulic pump.

I'm curious to know what length of delivery time people have been experiencing when ordering a new tractor from Bobcat.

I've been looking at the CT335 with a cab and comparing to it similar size Kubota and trying to decide which one to purchase. I'll be using the tractor in the bush in the fall to get firewood (were things unexpectedly stick up out of the ground) and one of the things I noticed on the CT335 is...

I have a 2002, L3010DST that just starting giving me a problem with the glow plug system. I go to start the engine the glow plug light comes on for 20-30 seconds then goes out and I start the engine with no problem. Then anywhere from a couple a seconds to several minutes after the engine starts...

I'm considering putting a Horst welding series 1000 snow blade on my Kubota L3010 with a LA482 loader. They make a 72" and 78" wide blade, from what I've read it would seem I should go for the 72" blade which when angles gives a 62" overall width. My question is would I be over-stressing the FEL...

I have an L3010 with a LA482 loader with a joystick control. I'm considering purchasing the Kubota L2172A (72" front mount blade. I was wondering if anyone has any experience with this blade specifically what quick-hitch and bracket/brace support kit I require for this blade to fit on this model...

I want to add a a single Spool Remote HYD Valve to my L3010. I've been told that if I order the Kubota L8407 kit, all the parts I need for this installation are part of this kit. I've also been told that I also have to order a handle kit to go with the above kit as well; except I can't find any...

I'm considering purchasing a Foton 404 with cab and loader for use in Canada's northern territories. I was wondering what experince people might have had running these tractors in cold temperatures -25C or less. My other concern is getting parts for these units as there is no dealer close to...